Husqvarna 372XP, 365 manual Lubricating cutting equipment, Chain oil, Filling with chain oil

Page 13

SAFETY INSTRUCTIONS

•Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner. Tighten the chain until it does not sag from the underside of the bar.

•Use the combination spanner to tighten the bar nuts while lifting the tip of the bar at the same time. Check that you can pull the chain round freely by hand and that it does not sag from the underside of the bar.

Lubricating cutting equipment

WARNING! Poor lubrication of cutting

!equipment may cause the chain to snap, which could lead to serious, even fatal injuries.

Chain oil

Chain oil must demonstrate good adhesion to the chain and also maintain its flow characteristics regardless of whether it is warm summer or cold winter weather.

As a chain saw manufacturer we have developed an optimal chain oil which, with its vegetable oil base, is also biodegradable. We recommend the use of our own oil for both maximum chain life and to minimise environmental damage. If our own chain oil is not available, standard chain oil is recommended.

In areas where oil specifically for lubrication of saw chains is unavailable, ordinary EP 90 transmission oil may be used.

Never use waste oil! This is dangerous for yourself, the machine and the environment.

Filling with chain oil

•All our chain saws have an automatic chain lubrication system. On some models the oil flow is also adjustable.

•The sizes of the chain oil tank and fuel tank have been chosen so that the engine will run out of fuel before running out of oil. This means that you should never run with a dry chain.

However, this safety feature requires that you use the right sort of chain oil (if the oil is too thin it will run out before the fuel), and that you adjust the carburettor as recommended (a weak mixture may mean that the fuel lasts longer than the oil) and that you also use the recommended cutting equipment (a bar that is too long will use more chain oil). The above conditions also apply to chain saw models with an adjustable oil pump.

Checking chain lubrication

•Check the chain lubrication each time you refuel.

Aim the tip of the bar at a light coloured surface about 20 cm (8 inches) away. After 1 minute running at 3/4 throttle you should see a distinct line of oil on the light surface.

If the chain lubrication is not working:

•Check that the oil channel in the bar is not obstructed. Clean if necessary.

•Check that the groove in the edge of the bar is clean. Clean if necessary.

•Check that the bar tip sprocket turns freely and that the lubricating hole in the tip sprocket is not blocked. Clean and lubricate if necessary.

If the chain lubrication system is still not working after carrying out the above checks and associated measures you should contact your service agent.

English – 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 362XP 365 372XP Key to symbols KEY to SymbolsContents Machine′s safety equipment Safety InstructionsPersonal protective equipment Chain brake and front hand guard Throttle lock Stop switchChain catcher Right hand guardChecking brake band wear MufflerChecking the front hand guard Checking the inertia brake releaseThrottle lock Stop switchChain catcher Right hand guardGeneral rules Cutting equipmentCutting equipment designed to minimise kickback MufflerSome terms that describe the bar and chain ChainGeneral information on sharpening cutting teeth Sharpening your chain and adjusting raker clearanceSharpening cutting teeth With a badly sharpened chainSetting the raker clearance General advice on setting raker clearanceTensioning the chain If the raker clearance is too largeChain oil Lubricating cutting equipmentFilling with chain oil Checking chain lubricationNeedle bearing lubrication Lubricating the bar tip sprocketChecking wear on cutting equipment Chain drive sprocketWhat is kickback? How to avoid kickbackDo not let go of the handles General safety precautions Starting Fuel safetyTransport and storage General working instructions Basic safety rulesBasic cutting technique GeneralCutting TermsLimbing Tree felling techniqueSafe distance Felling directionDirectional cuts FellingFelling cut Freeing a tree that has fallen badly General adviceCutting the trunk into logs Freeing a trapped treeWhat is what on the chain saw? What is WHAT?Fitting the bar and chain AssemblyFitting a spike bumper Working with the chainFuel Fuel HandlingMin 3 m 10ft FuellingStarting and stopping Starting and StoppingCold engine Warm engineStopping Carburettor MaintenanceStarter Correctly adjusted carburettorHigh speed jet H Changing a broken or worn starter cordSpark plug Air filterTensioning the recoil spring Changing a broken recoil springWhen making adjustments Adjustment of the oil pumpMuffler Needle bearing lubricationHeated handles Air Injection centrifugal cleaningElectrical carburettor heating Winter useWeekly maintenance Daily maintenanceMonthly maintenance Below you will find some general maintenance instructionsTechnical data Technical DataBar Chain Bar and chain combinationsApplies to Europe only EC-declaration of conformityEN292-2, Cispr 121997, EN608 ´z+H4¶6j¨ Page 1140206-26 ´z+H4¶6j¨ ´z+H4¶6j¨
Related manuals
Manual 4 pages 16.24 Kb

372XP, 365 specifications

The Husqvarna 365 and 372XP chainsaws are powerful and versatile tools designed for both professional loggers and serious homeowners. Known for their robust construction and reliability, these models offer a perfect blend of performance and user-friendly features.

The Husqvarna 365 is equipped with a 70.7 cc engine that delivers impressive power, making it suitable for demanding cutting tasks. This chainsaw is designed for all-day use, ensuring that operators can tackle large trees and tough woods without losing momentum. The engine utilizes Smart Start technology, which allows for easier starting with minimal effort. This innovation reduces the resistance in the starter cord by up to 40%, enabling rapid and hassle-free ignition.

On the other hand, the Husqvarna 372XP boasts a slightly larger 72.2 cc engine, making it one of the most powerful saws in the market. Specifically tailored for professionals, this chainsaw excels in heavy-duty applications and has the ability to handle extreme workloads. Both models are designed with a high RPM, ensuring smooth cutting performance and efficient chip flow, which contributes to cleaner cuts and enhanced productivity.

A significant feature of these chainsaws is their ergonomic design, which includes a comfortable handle for better grip and control during operation. The chainsaws also feature an adjustable oil pump that allows users to customize the oil flow for the chain and bar, which helps minimize wear and prolongs the lifespan of the saw.

Safety is paramount with both the 365 and 372XP models. They are equipped with a chain brake system that automatically stops the chain in the event of kickback, ensuring user protection. Furthermore, the low vibration technology significantly reduces vibrations experienced by the operator, promoting comfort during prolonged use.

In terms of maintenance, both chainsaws come with a quick-release air filter that makes it easy to access and clean, ensuring optimal engine performance over time. The built-in fuel pump facilitates easier starting after long periods of inactivity, making these tools reliable for various cutting tasks.

In summary, the Husqvarna 365 and 372XP chainsaws stand out for their powerful engines, user-friendly features, and advanced safety technologies. They are engineered to meet the high demands of professional users while also being accessible for those who need a reliable chainsaw for home use. Whether for felling trees or limbing, these models deliver excellence in performance and durability.
Top Page Image Contents