Husqvarna WH4817EFQ2, WH5219EFQ manual Changing the Oil Filter

Page 55

LUBRICATION

The oil level should lie between the markings on the dipstick. If the level is approaching the ”ADD” mark, fill the oil to the ”FULL” mark on the dipstick.

Never fill above the ”FULL” mark.

The oil is filled through the hole the dipstick sits in.

Use engine oil SAE 30 or SAE 10W-30 or, alternately, 10W/40, class SF–SJ

(over +32 °F / 0 °C).

Over +68 °F / +20 °C SAE 40 can be used.

Use engine oil SAE 5W-20, class SF–SJ (under +32 °F / 0 °C).

The engine holds 1.6 qt (1.5 liters) of oil excluding the filter (including filter 1.8 qt, 1.7 liters).

7. Changing the Oil Filter

1.Drain the engine oil in accordance with the work description under the heading Engine Oil/Change Engine Oil.

2.Remove the oil filter. If necessary, use a filter remover.

3.Wipe new, clean engine oil onto the seal for the new filter.

4.Mount the filter by hand with + 3/4 turn.

5.Run the engine warm, then check that there are no leaks around the oil filter seal.

6.Check the oil level in the engine, top up if necessary. The oil filter holds 0.2 qt (0.2 liters) of oil.

8009-159

The dipstick markings

8009-140

Engine oils

8011-782

Changing the oil filter

English-53

Image 55

Contents

WH4817EFQ/968999252 WH5219EFQ/968999253 Page OPERATOR’S Manual Mower WH4817EFQ WH5219EFQ ContentsEnglish-2 Introduction IntroductionManufacturing Number Good ServiceSymbols and Decals Symbols and DecalsXxxxxxx xxxx xxxxxxxx xxx Xxxx xxxxxx Keep a safe Safety Instructions Safety InstructionsGeneral Use Age of the user Do as follows Driving on SlopesDo not Children Maintenance Risk of sparking Use protective glasses at maintenance work Customer responsibilities TransportControl Locations ControlsGround Speed Lever Ignition SwitchChoke Control Throttle Control Operator Presence LeverNeutral Bail Blade Engagement SwitchParking Brake Motion control levers Hour MeterRefueling Tracking KnobFuses Fuel Shut-off ValveClose fuel valve at the end of each mowing job Pump release valves Lifting Lever for the Mower DeckAccessories To move forward and backward OperationOperation TrainingStarting the Engine Before StartingNeutral lock bail, locked position RPM to maximum To start an engine with a weak battery Reversing RunningMowing Tips To operate on hillsClean mower deck after each use Emergency stop StoppingNormal operating stop Stopping the Engine Floating deck machines Adjustment of cutting heightWheel Motor Adjustment Moving Machine by HandMaintenance MaintenanceMaintenance Schedule English-36 To clean or replace battery and terminals BatteryIgnition System Functional check Checking the Safety SystemChecking and Adjusting the Choke Cable Checking and Adjusting Throttle CableChecking the Engines Cooling Air Intake Replacing the Air Filter Checking the Fuel Pump’s Air Filter Replacing the Fuel FilterChecking Tire Pressures Deck belt Checking the V-beltsPump belt Checking the BladesAdjusting Cutting Height Adjusting the Mower DeckLeveling To adjust anti-scalp rollers Caster Wheels Cleaning and WashingHardware Blade replacement Lubrication Lubrication Lubrication Schedule Front Wheel Bearings Lubricating the CablesLubricating in Accordance with the Lubrication Schedule Front Wheel MountThrottle and Choke Cables, Lever Bearings Belt Adjuster, Mower DeckChecking the Oil Level Engine Oil Changing the Engine OilChanging the Oil Filter Hydraulic System, Oil Level Mower Deck Height AdjusterChanging Oil and Filters Trouble Shooting Guide Trouble Shooting GuideProblem Cause Rich fuel mixture or fuel-air mixture English-57 Winter Storage ServiceStorage StorageWiring diagrams Wiring DiagramsWiring Diagram Transmission Technical DataTechnical Data EngineOverall dimensions Torque SpecificationsUSA requirements Conformity CertificatesAfter the First 8 Hours Service JournalService Journal Delivery ServiceHour Service English-66 English-67 English-68 At Least Once Each Year 110585R0108/10/05