Husqvarna YTH18542 owner manual Mowing Tips, Purge Transmission, Automatic Transmission Warm UP

Page 14

OPERATION

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING ( 50° F and below)

•When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast posi- tion. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Place the motion control lever in neutral. Release the parking brake and let the clutch/brake slowly return to operating position.

•Allow one minute for transmission to warm up.This can be done during the engine warm up period.

•The attachments can also be used during the engine warm-up period after the transmission has been warmed up.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is run-

ning.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de- veloped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

•Move motion control lever to neutral (N) position. Shut- off engine and set parking brake.

•Engage transmission by placing freewheel control in engaged position (See “TO TRANSPORT” in this sec- tion of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

•Slowly move motion control lever forward, after the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the tractor moves approximately five (5) feet return the motion control lever to the neutral (N) position. Repeat this procedure with the motion control lever three (3) times.

•Your transmission is now purged and now ready for normal operation.

MOWING TIPS

•Mower should be properly leveled for best mowing per- formance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trim- ming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting.

•When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 9).

•Place tractor safely on level surface with engine off and parking brake set.

•Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral (N) position, slowly dis- engage clutch/brake pedal.

•Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times.

NOTE: During this procedure there will be no movement of drive wheels. The air is being removed from hydraulic drive system.

FIG. 9

• If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

• Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

• Always operate engine at full throttle when mow- ing to assure better mowing performance and proper discharge of material. Regulate ground speed by se- lecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

• When operating attachments, select a ground speed that will suit the terrain and give best performance of

14

the attachment being used.

Page 13 Page 15
Image 14
Page 13 Page 15
Contents 917.279060 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIV. Towing ServiceIII. Children Table of Contents Seat Unassembled PartsSteering Wheel To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsCheck Engine OIL Level Before Starting the EngineTo Transport See Figs ADD GasolineAutomatic Transmission Warm UP Mowing TipsPurge Transmission General Recommendations MaintenanceLubrication Chart Before Each USETo Sharpen Blade See Fig TractorBlade Removal See Fig Check Operator Presence SystemEngine Cleaning To Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig See Fig To Check and Adjust BrakeTransaxle Motion Control Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Engine dies when Schematic TRACTOR-MODEL Number YTH18542 917.279060, Product no 13Electrical KEY Part NO. NO. Description Chassis TRACTOR-MODEL Number YTH18542 917.279060, Product no 13 Drive TRACTOR-MODEL Number YTH18542 917.279060, Product no 13 Steering Assembly TRACTOR-MODEL Number YTH18542 917.279060, Product no 13 Engine Optional EquipmentMower Lift 1331Seat Assembly Decals Wheels and TiresMower Deck TRACTOR-MODEL Number YTH18542 917.279060, Product no 13 Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement 532 19 58-63 Rev 3.18.05 RD
Related manuals
Manual 17 pages 30.7 Kb

YTH18542 specifications

The Husqvarna YTH18542 is a versatile and efficient lawn mower designed to meet the needs of homeowners looking for a reliable and high-performing machine for maintaining their lawns. Its robust design and advanced features make it a popular choice among gardening enthusiasts and professionals alike.

One of the standout features of the YTH18542 is its powerful 18.5 HP Briggs & Stratton engine. This engine provides ample power to tackle various lawn conditions, ensuring that grass cutting is smooth and efficient. The engine is designed for durability and ease of maintenance, allowing users to focus more on mowing and less on upkeep.

The YTH18542 is equipped with a 42-inch cutting deck that boasts a reinforced structure for added longevity. This cutting deck offers a variety of cutting heights, adjustable with a simple lever, which allows users to achieve their desired grass length easily. The wide cutting path minimizes mowing time while providing a clean, even cut.

In terms of comfort, the tractor features an ergonomic design with a comfortable seat, making longer mowing sessions less taxing. The easy-to-use steering wheel provides excellent maneuverability, allowing the operator to navigate tight corners and obstacles within the yard smoothly. Additionally, the implementation of a pedal-operated hydrostatic transmission ensures seamless speed control without the need for manual gear shifting.

Husqvarna's commitment to innovation is evident in the design of the YTH18542. The machine features a tight turning radius, which enhances agility and efficiency when working around flower beds, trees, and slopes. The mower also supports attachments, enabling users to expand its functionality with tools such as baggers or mulchers, making it a multi-season investment.

The mower includes safety features like an automatic blade engagement, which instantly starts the cutting blades only when the operator is seated. This promotes safety and reduces the risk of accidents.

Lastly, the YTH18542 possesses an aesthetically pleasing design, with a bright orange finish that is striking in any landscape. Its combination of performance, comfort, and safety features makes the Husqvarna YTH18542 a top choice for anyone seeking efficiency and quality in lawn care. With its dependable performance and innovative technologies, this mower is well-suited for various yard sizes and complexities.
Top Page Image Contents