Husqvarna YTH18542 To Check and Adjust Brake, To Replace Motion Drive Belt See Fig

Page 21

SERVICE AND ADJUSTMENTS

TO CHECK AND ADJUST BRAKE

(See Fig. 21)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.

TO CHECK BRAKE

Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and en- gage parking brake.

Disengage transmission by placing freewhel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE

Depress clutch/brake pedal all the way down and en- gage parking brake.

Measure distance between brake operating arm and nut “A” on brake rod.

If distance is other than 1-9/16", loosen jam nut and turn nut “A” until distance becomes 1-9/16". Retighten jam nut against nut “A”.

Engage transmission by placing freewheel control in “transmission engaged” position.

Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center.

WITH PARKING BRAKE “ENGAGED”

NUT “A”

1-9/16”

JAM NUT

 

OPERATING

ARM

01513

DO NOT TOUCH THIS NUT. IF FURTHER BRAKE ADJUST- MENT IS NECESSARY CONTACT YOUR NEAREST AUTHO- RIZED SERVICE CENTER/DEPARTMENT

FIG. 21

TO REPLACE MOTION DRIVE BELT (See Fig. 22)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

Disconnect clutch wire harness.

Remove clutch locator.

Remove belt from stationary idler and clutching idler.

Remove belt downward from engine pulley and around electric clutch.

Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

Carefully work new belt down around transmission cooling fan and onto the input pulley.

Slide belt into the center span keeper.

Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley.

Install belt through stationary idler and clutching idler.

Reinstall clutch locator and tighten nut securely.

Reconnect clutch harness.

Make sure belt is in all pulley grooves and inside all belt guides and keepers.

Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

ELECTRIC

CLUTCH LOCATOR

CLUTCH

 

CLUTCHING

IDLER

STATIONARY

IDLER

CENTER SPAN

KEEPER

TRANSMISSION

CLUTCH

INPUT PULLEY

WIRE

 

HARNESS

FIG. 22

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 23)

The motion control lever has been preset at the factory and adjustment should not be necessary.

Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

Start engine and move motion control lever until tractor does not move forward or backward.

21

Image 21
Contents 917.279060 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Unassembled Parts Steering WheelSeat Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigReverse Operation System ROS To Operate on HillsTo Transport See Figs Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Lubrication Chart MaintenanceGeneral Recommendations Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Check Operator Presence SystemEngine Cleaning To Install Mower See Fig Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal Transaxle Motion Control Lever Neutral Adjustment See Fig To Check and Adjust BrakeSee Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILTroubleshooting Points Engine dies when TRACTOR-MODEL Number YTH18542 917.279060, Product no 13 SchematicElectrical KEY Part NO. NO. Description Chassis TRACTOR-MODEL Number YTH18542 917.279060, Product no 13 Drive TRACTOR-MODEL Number YTH18542 917.279060, Product no 13 Steering Assembly TRACTOR-MODEL Number YTH18542 917.279060, Product no 13 Optional Equipment Engine1331 Mower LiftSeat Assembly Wheels and Tires DecalsMower Deck TRACTOR-MODEL Number YTH18542 917.279060, Product no 13 Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationWarranty Statement 532 19 58-63 Rev 3.18.05 RD
Related manuals
Manual 17 pages 30.7 Kb

YTH18542 specifications

The Husqvarna YTH18542 is a versatile and efficient lawn mower designed to meet the needs of homeowners looking for a reliable and high-performing machine for maintaining their lawns. Its robust design and advanced features make it a popular choice among gardening enthusiasts and professionals alike.

One of the standout features of the YTH18542 is its powerful 18.5 HP Briggs & Stratton engine. This engine provides ample power to tackle various lawn conditions, ensuring that grass cutting is smooth and efficient. The engine is designed for durability and ease of maintenance, allowing users to focus more on mowing and less on upkeep.

The YTH18542 is equipped with a 42-inch cutting deck that boasts a reinforced structure for added longevity. This cutting deck offers a variety of cutting heights, adjustable with a simple lever, which allows users to achieve their desired grass length easily. The wide cutting path minimizes mowing time while providing a clean, even cut.

In terms of comfort, the tractor features an ergonomic design with a comfortable seat, making longer mowing sessions less taxing. The easy-to-use steering wheel provides excellent maneuverability, allowing the operator to navigate tight corners and obstacles within the yard smoothly. Additionally, the implementation of a pedal-operated hydrostatic transmission ensures seamless speed control without the need for manual gear shifting.

Husqvarna's commitment to innovation is evident in the design of the YTH18542. The machine features a tight turning radius, which enhances agility and efficiency when working around flower beds, trees, and slopes. The mower also supports attachments, enabling users to expand its functionality with tools such as baggers or mulchers, making it a multi-season investment.

The mower includes safety features like an automatic blade engagement, which instantly starts the cutting blades only when the operator is seated. This promotes safety and reduces the risk of accidents.

Lastly, the YTH18542 possesses an aesthetically pleasing design, with a bright orange finish that is striking in any landscape. Its combination of performance, comfort, and safety features makes the Husqvarna YTH18542 a top choice for anyone seeking efficiency and quality in lawn care. With its dependable performance and innovative technologies, this mower is well-suited for various yard sizes and complexities.