Husqvarna Key Steps for YTH18542 Battery Replacement, Transmission Service, and Tire Adjustments
Page 22

SERVICE AND ADJUSTMENTS

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satis- fied.

MOTION CONTROL

NEUTRAL

LEVER

LOCK GATE

 

ADJUSTMENT

BOLT

FIG. 23

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor.If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 24)

• Block up axle securely.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 24

TO START ENGINE WITH A WEAK BATTERY (See Fig. 25)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

• Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

• Repair tire and reassemble.

• On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

• Replace washers and snap retaining ring securely in axle groove.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

• Replace axle cover.

22

FIG. 25

Page 21 Page 23
Image 22
Page 21 Page 23
Contents 917.279060 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceIV. Towing Table of Contents Steering Wheel Unassembled PartsSeat To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsCheck Engine OIL Level Before Starting the EngineTo Transport See Figs ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP General Recommendations MaintenanceLubrication Chart Before Each USETo Sharpen Blade See Fig TractorBlade Removal See Fig Check Operator Presence SystemEngine Cleaning To Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal See Fig To Check and Adjust BrakeTransaxle Motion Control Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Engine dies when Schematic TRACTOR-MODEL Number YTH18542 917.279060, Product no 13Electrical KEY Part NO. NO. Description Chassis TRACTOR-MODEL Number YTH18542 917.279060, Product no 13 Drive TRACTOR-MODEL Number YTH18542 917.279060, Product no 13 Steering Assembly TRACTOR-MODEL Number YTH18542 917.279060, Product no 13 Engine Optional EquipmentMower Lift 1331Seat Assembly Decals Wheels and TiresMower Deck TRACTOR-MODEL Number YTH18542 917.279060, Product no 13 Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement 532 19 58-63 Rev 3.18.05 RD
Related manuals
Manual 17 pages 30.7 Kb

YTH18542 specifications

The Husqvarna YTH18542 is a versatile and efficient lawn mower designed to meet the needs of homeowners looking for a reliable and high-performing machine for maintaining their lawns. Its robust design and advanced features make it a popular choice among gardening enthusiasts and professionals alike.

One of the standout features of the YTH18542 is its powerful 18.5 HP Briggs & Stratton engine. This engine provides ample power to tackle various lawn conditions, ensuring that grass cutting is smooth and efficient. The engine is designed for durability and ease of maintenance, allowing users to focus more on mowing and less on upkeep.

The YTH18542 is equipped with a 42-inch cutting deck that boasts a reinforced structure for added longevity. This cutting deck offers a variety of cutting heights, adjustable with a simple lever, which allows users to achieve their desired grass length easily. The wide cutting path minimizes mowing time while providing a clean, even cut.

In terms of comfort, the tractor features an ergonomic design with a comfortable seat, making longer mowing sessions less taxing. The easy-to-use steering wheel provides excellent maneuverability, allowing the operator to navigate tight corners and obstacles within the yard smoothly. Additionally, the implementation of a pedal-operated hydrostatic transmission ensures seamless speed control without the need for manual gear shifting.

Husqvarna's commitment to innovation is evident in the design of the YTH18542. The machine features a tight turning radius, which enhances agility and efficiency when working around flower beds, trees, and slopes. The mower also supports attachments, enabling users to expand its functionality with tools such as baggers or mulchers, making it a multi-season investment.

The mower includes safety features like an automatic blade engagement, which instantly starts the cutting blades only when the operator is seated. This promotes safety and reduces the risk of accidents.

Lastly, the YTH18542 possesses an aesthetically pleasing design, with a bright orange finish that is striking in any landscape. Its combination of performance, comfort, and safety features makes the Husqvarna YTH18542 a top choice for anyone seeking efficiency and quality in lawn care. With its dependable performance and innovative technologies, this mower is well-suited for various yard sizes and complexities.
Top Page Image Contents