Husqvarna YTH18K46 owner manual To Operate Mower, To Stop Mower Blades

Page 10

OPERATION

TO MOVE FORWARD AND BACKWARD (See Fig. 7)

The direction and speed of movement is controlled by the forward and reverse drive pedals.

•Start tractor and release parking brake.

•Slowly depress forward (K) or reverse (L) drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.

TO USE CRUISE CONTROL (J) (See Fig. 7)

The cruise control feature can be used for forward travel only.

JK L

Fig. 7

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

Fig. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in prop- er position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjustmowertodesiredcuttingheight(See“TOADJUST MOWER CUTTING HEIGHT” in this section of manual).

•Withmowerindesiredheightofcutposition,gaugewheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

Fig. 9

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut (see "TO ADJUST MOWER CUTTING HEIGHT")

•Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES

Disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector chute

(S) in place (See Fig. 10).

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Operator’s Manual EnglishSafety Rules Safe Operation Practices for Ride-On MowersIII. Children General ServiceSafe Handling of Gasoline Table of Contents Unassembled Parts AssemblyTools Required for Assembly ToremovetractorfromcartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Stopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig To USE Throttle Control D See FigTo Operate Mower To Stop Mower BladesReverse Operation System ROS See Fig Service REMINDER/HOUR MeterUsing the Reverse Operation System To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigTransaxle Cooling EngineBelts Transaxle Pump FluidCleaning Deck Washout Port See Fig To Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerTo Check Brake Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove Wheel for Repairs See FigTransmission Fuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine continues Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXConsumer Wheeled Products Limited Warranty HOW to Obtain Service Consumer Wheeled Limited Warranty Chart Consumer Wheeled Limited Warranty Chart 08/27/2012 BD

YTH18K46 specifications

The Husqvarna YTH18K46 is a robust and versatile riding lawn mower designed for homeowners seeking an efficient and reliable solution for maintaining their lawns. This compact tractor combines power, performance, and ease of use, making it an ideal choice for medium to large-sized yards.

One of the standout features of the YTH18K46 is its powerful 18-horsepower Kohler engine. This reliable engine ensures that users can tackle even the toughest mowing tasks with confidence. The engine is specifically designed for efficiency, providing an excellent balance of power and fuel economy, making it an environmentally friendly option as well.

The 46-inch cutting deck is another highlight of the YTH18K46. This wide deck allows for efficient mowing, covering more ground in less time. The cutting height can be easily adjusted from 1.5 to 4 inches, allowing homeowners to choose the perfect height for their grass. This versatility ensures that your lawn looks well-groomed, regardless of the season.

For added convenience, the YTH18K46 features an automatic choke system, making starting the mower easier without the hassle of manually adjusting choke settings. The pedal-operated hydrostatic transmission provides smooth and effortless speed control, allowing users to navigate their yards with precision.

The comfortable high-back seat, along with an ergonomic steering wheel, enhances the overall mowing experience. With added features such as a built-in cup holder and an easy-to-read fuel gauge, user comfort is prioritized during every mowing session.

Safety is also a key focus with the Husqvarna YTH18K46. It is equipped with an automatic blade engagement system that ensures the blades turn off when the operator leaves the seat, preventing accidents. Furthermore, the anti-scalp wheels on the cutting deck help prevent scalping of the turf, ensuring a clean and even cut.

In summary, the Husqvarna YTH18K46 is a powerful and practical riding mower that combines innovative technologies and thoughtful design. With its reliable engine, versatile cutting deck, and user-friendly features, it caters to the needs of homeowners looking for efficiency and comfort in lawn care. Whether you’re dealing with a sprawling lawn or navigating tight spaces, the YTH18K46 is built to deliver exceptional performance and results.
Top Page Image Contents