Husqvarna PZ6029D, PZ29D BF manual Battery, For cleaning, For replacing

Page 40

maintenance

Battery

The mower is equipped with a maintenance free battery and does not need servicing. However, periodic charging of the battery with an automotive type battery charger will extend its life.

Keep battery and terminals clean.

Keep battery bolts tight.

See chart for charging times.

WARNING!

Always wear eye protection when around batteries.

Battery Removal

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

1.Lift the seat and rotate fully forward until supported by the seat rod.

2.Loosen the two wingnuts attached to the side “J” bolts just enough that the battery mount bracket slides down off the battery.

3.Using two ½" wrenches disconnect BLACK battery cable then RED battery cable.

4.Carefully remove the battery from the mower.

For cleaning

5.Rinse the battery with plain water and dry.

6.Clean terminals and battery cable ends with wire brush until shiny.

For replacing

7.Install new battery with terminals in the same position as the old battery.

8.Connect RED battery cable first to positive (+) battery terminal.

9.Connect BLACK grounding cable to negative (-) battery terminal.

10.Slide mount bracket back up over battery and retighten wingnuts.

11.Lower seat.

STANDARD

STATE

APPROXIMATE BATTERY CHARGING TIME*

 

 

TO FULL CHARGE AT 80OF / 27OC

BATTERY

OF

 

 

 

 

 

Maximum Rate at:

 

 

 

 

 

 

CHARGE

 

 

 

 

 

50 Amps

30 Amps

20 Amps

10 Amps

 

 

 

 

 

 

 

 

12.6V

100%

- FULL CHARGE -

 

 

 

 

 

 

12.4V

75%

20 min.

35 min.

48 min.

90 min.

 

 

 

 

 

 

12.2V

50%

45 min.

75 min.

95 min.

180 min.

 

 

 

 

 

 

12.0V

25%

65 min.

115 min.

145 min.

280 min.

 

 

 

 

 

 

11.8V

0%

85 min.

150 min.

195 min.

370 min.

 

 

 

 

 

 

*Charging time depends on battery capacity,

condition, age, temperature and efficiency of charger

IMPORTANT INFORMATION

Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

Always use two wrenches for the terminal screws.

WARNING!

Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparks from accidental grounding.

1

2

8065-020

1.Mount bracket

2.Battery bracket

Battery cleaning and installation

40

Image 40
Contents Operator Manual Page Contents Page Introduction Good Service Manufacturing NumberSymbols and decals Manual Performing any Safety Instructions SafetyGeneral Operation Never take passengers Personal Safety Equipment Slope OperationChildren Safe Handling of Diesel Fuel General Maintenance Risk of sparking Transport Rollover Protection System Rops Spark ArrestorsControls Control LocationsMotion Control Levers Tracking Knob Parking BrakeIgnition Switch Blade SwitchHour Meter Ignition switch RUN position Battery Voltage Coolant TemperatureControl Module Oil PressureSeat Adjustments Cutting Height PedalsFuses Fuel Shut Off ValveRefueling Training OperationSteering Roll Bar and Safety Belt Before StartingStarting the Engine Set the throttle Set the engine speed Jumper Cables Weak BatteryTo remove cables, reverse order Running Ensure that no one is near mower when engaging blade switch Operating on HillsStopping the Engine Mowing Tips Manual Transport Maintenance Engine and RadiatorMaintenance For cleaning BatteryFor replacing Fuel Filter Safety SystemTire Pressures Parking brake adjustment Height Adjustment Drive Lever AdjustmentAlignment Pump Neutral Adjustment Deck Belt Deck Belt InstallationDeck Belt Removal Pump Belt Belt Removal/InstallationReplacing Pump Belt Reinstallation Clutch BeltBelts RemovalCutting Blades Adjusting the Mower Deck Leveling DeckRemoval and Installation Caster WheelsAnti-scalp Rollers Deck Lift SpringUse protective glasses when cleaning and washing CleaningHardware Lubrication Schedule LubricationGeneral Wheel and Deck Zerks CablesFront Wheel Mount Front Wheel BearingsHydraulic Drive Fluid and Filter ChangeTransmission Purging Procedures Troubleshooting guide Problem CauseTroubleshooting guide Storage ServiceWinter Storage Wiring Diagram PZ6029D PZ29D BF Engine Technical DataTransmission Dimension PZ6029D PZ29D BF FrameTorque Specifications Hex Head Cap ScrewsStandard Hardware Metric Standard HardwareUSA requirements CE requirementsService Journal Delivery ServiceAfter 10 hours Daily Service Hour Service Service Journal Service Journal At Least Once Each Year Page 115 326227R1 02/25/10

PZ6029D, PZ29D BF specifications

The Husqvarna PZ29D BF and PZ6029D are two powerful members of Husqvarna’s range of commercial-grade zero-turn mowers, designed to meet the needs of both professional landscapers and avid homeowners seeking efficiency and performance. These models stand out with their combination of robust construction, advanced features, and innovative technologies, ensuring they can handle the most demanding mowing tasks with ease.

The PZ29D BF is equipped with a durable 29-horsepower diesel engine, offering exceptional torque and fuel efficiency. This powerhouse, combined with a heavy-duty steel frame, provides stability and longevity, ensuring the unit can withstand rigorous use in varied landscaping environments. The mower's commercial-grade cutting deck, available in multiple widths, allows for precision mowing, while its reinforced edges minimize wear and tear, extending the mower's lifespan.

On the other hand, the PZ6029D features a larger cutting deck, making it ideal for extensive lawns and commercial properties. With a maximum speed of 10 miles per hour, this model allows for rapid mowing, significantly reducing the time spent on the job. Both models are equipped with an adjustable cutting height, enabling the user to customize mowing according to grass type and terrain, promoting healthier lawns.

One of the main technological highlights of these mowers is their hydraulic drive system, which provides unmatched maneuverability. The intuitive controls allow users to quickly navigate tight spaces and obstacles, ensuring a smooth mowing experience. Moreover, both the PZ29D BF and PZ6029D feature a high-back seat with lumbar support, making long hours of mowing more comfortable for the operator.

The innovative air filtration system in both models enhances engine life by ensuring cleaner air intake, leading to improved performance over time. Additionally, the easy-access maintenance points simplify routine upkeep, giving users more time to focus on the task at hand.

Another noteworthy characteristic of these zero-turn mowers is their quiet operation, which is crucial for residential areas and noise-sensitive environments. The construction is not just strong but designed to reduce vibrations, contributing to operator comfort while enhancing overall durability.

In conclusion, the Husqvarna PZ29D BF and PZ6029D are high-performance zero-turn mowers that combine power, efficiency, and ease of use. Their advanced features make them perfect for tackling large mowing tasks while ensuring operator comfort and machine longevity. Whether for a commercial landscape or a spacious backyard, these mowers are built to deliver exceptional results.