Husqvarna YTH1342XP owner manual To Adjust Steering Wheel Alignment, Front Wheel TOE-IN/CAMBER

Page 22

SERVICE AND ADJUSTMENTS

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satis- fied.

MOTION

NEUTRAL

CONTROL

LOCK GATE

LEVER

 

ADJUSTMENT

BOLT

FIG. 25

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 26)

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

 

 

FIG. 26

TO START ENGINE WITH A WEAK BATTERY (See Fig. 27)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

BLACK cable first from chassis and then from the fully charged battery.

RED cable last from both batteries.

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

22

FIG. 27

 

Page 21 Page 23
Image 22
Page 21 Page 23
Contents YTH1342XP General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Table of Contents Blade Unassembled PartsSteering Wheel Seat KeyTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidInstall Seat See Fig To SET UP Your Mower for MulchingCheck Deck Levelness To Convert to Bagging or DischargingCheck Tire Pressure Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Mulching Mowing TipsService Dates MaintenanceLubrication Chart General RecommendationsTractor Engine Spark Plugs CleaningMuffler Engine OIL FilterTo Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal Transaxle Motion Control Lever Neutral ADJUSTMENTSee Fig To Check and Adjust Brake See FigTransmission REMOVAL/REPLACEMENT To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig To Remove Wheel for Repairs See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Carburetor Interlocks and RelaysFuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor Model NO. YTH1342XP YTH1342XPA, Product no 56Electrical KEY Part Description Chassis and Enclosures 532 18 Drive Repair Parts Steering Assembly 532 18 Wheel Steering Seat Assembly 532 18 SeatDecals 532 17Repair Parts EngineMower Lift Mower Deck 532 17 Belt Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement 532 18 44-43 Rev 03.20.03 RH/MH/RH/TR

YTH1342XP specifications

The Husqvarna YTH1342XP is a reliable and efficient riding lawn mower that caters to the needs of homeowners with medium to large-sized lawns. This advanced mower model brings together a robust construction, modern technologies, and user-friendly features, creating an exceptional mowing experience.

At the heart of the YTH1342XP is its powerful 13.5 HP Kohler engine, providing ample power to handle tough grass conditions with ease. The engine is designed for durability and longevity, ensuring that it can withstand regular use season after season. With a hydrostatic transmission, the mower offers smooth and effortless speed adjustments, allowing users to navigate different terrains without experiencing bumps or transitions.

The YTH1342XP features a 42-inch cutting deck that provides effective coverage and makes mowing faster and more efficient. The deck is constructed from high-quality materials, ensuring longevity and resistance to wear and tear. It also has a reinforced cutting deck that enables the mower to tackle taller grass and dense underbrush.

One of the standout characteristics of the YTH1342XP is its cutting height adjustment, which allows users to select from multiple cutting heights based on the specific needs of their lawn. This flexibility ensures a precise and professional-looking finish, which is particularly valuable for lawn enthusiasts.

To enhance user comfort, the mower is equipped with a comfortable high-back seat and ergonomic steering, making long mowing sessions less tiresome. The easy-to-use dashboard includes intuitive controls that make starting the mower and adjusting settings simple.

The YTH1342XP is also compatible with several accessories, including baggers and mulch kits, which can be added to enhance the mower’s functionality. Furthermore, Husqvarna has engineered this model with advanced safety features, including an automatic shut-off function that engages when the driver leaves the seat.

In summary, the Husqvarna YTH1342XP is a robust riding mower that stands out for its powerful performance, versatile cutting options, and thoughtful design elements aimed at improving user experience. Whether maintaining a small yard or managing a larger lawn, this mower offers the efficiency, durability, and comfort that discerning homeowners demand.
Top Page Image Contents