Husqvarna 318 Driving, Before starting, Start the engine, Starting the engine with a weak battery

Page 14

Driving

Before starting

•Read the safety instructions and information concerning the placement of controls and functions before starting.

•Perform daily maintenance before starting as set out in the Maintenance schedule.

IMPORTANT INFORMATION

The air intake grille in the engine cover behind the driver’s seat must not be blocked by, for example, clothing, leaves, grass or dirt. Impaired cooling of the engine.

Risk of major engine damage.

Start the engine

1Make sure that the clutch control is depressed. Rider 320 AWD has one control for the front axle and one control for the rear axle.

2Lift up the cutting unit by pulling the lever backwards to locked position (transport position) and apply the parking brake.

Move the throttle in between positions 1 and 2.

1

2 3

5 Turn the ignition key to the start position.

STOP

START

6When the engine starts release the ignition key immediately back to neutral position.

STOP

START

IMPORTANT INFORMATION

Do not run the starter for more than about 5 seconds at a time. If the engine does not start, wait about 15 seconds before trying again.

7Push the throttle control to full throttle position. Let the engine run at moderate speed or half throttle for 3-5 minutes before subjecting it to heavy load.

8Set the required engine speed with the throttle control.

!

WARNING! Never run the engine indoors, in

enclosed or poorly ventilated areas. The

exhaust fumes contain toxic carbon

 

monoxide.

1

2

Starting the engine with a weak battery

3The engine can not be started if the parking brake is not pressed down.

Starting a cold engine

4Move the throttle to position 3 (choke position). In this position the engine is fed with a richer mixture, which means the engine is easier to start.

1 2

3

Starting a warm engine

!

WARNING! Lead-acid batteries produce

explosive gases. Avoid sparks, open flames

and smoking close to batteries. Always wear

 

protective glasses in the vicinity of batteries.

If the battery is too weak to start the engine, it should be recharged.

When jump leads are used for emergency starting, follow the procedure below:

IMPORTANT INFORMATIONYour Rider is equipped with a 12-volt system with negative earth. The other vehicle must also have a 12-volt system with negative earth. Do not use your Rider battery to start other vehicles.

14 – English

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Rider 318 Rider 320 AWD Contents After the first 8 hours Service journalPre-delivery service Introduction KEY to Symbols SymbolsStarting instructions What is WHAT? Location of the controlsInsure your Rider Safety InstructionsSafety instructions General useDriving on slopes This is what you doMaintenance ChildrenTransport Presentation Release lever SeatFueling Release lever RiderBefore starting Starting the engine with a weak batteryDriving Start the engineRemove the cables in the reverse order Connecting the jump leadsDriving the Rider Other objects which can be thrown out by the blades Cutting tipsStop the engine Maintenance Maintenance scheduleRemoving of the machine hoods CleaningChecking and adjusting the steering wires Checking and adjusting of throttle wire Adjusting the parking brake RiderAdjusting the parking brake Rider 320 AWD Can result in reduced braking abilityChecking the fuel pump’s air filter Replacement of fuel filterReplacing the air filter Cool before starting to replace the air filterMain fuse Check the safety systemIgnition system Checking the tyre pressureFitting the cutting head When the engine is running. Mind your fingersChecking the engine’s cooling air intake Trapping your handRemoving the cutting unit Replacing the cutting unit belts Adjusting the parallelism of the cutting unitChecking the cutting unit’s parallelism Service position for the cutting unit Placing in the service positionRemoving the BioClip plug Restoring from service positionChecking the blades Combi 103, CombiChanging the oil filter LubricationChecking the engine’s oil level Replacing the engine oilGeneral lubrication Lubricating the belt adjusterChecking the transmission oil level Troubleshooting schedule Winter storage ServiceStorage GuardTechnical Data Cutting unit Combi EC-declaration of conformity Applies to Europe only Page Page 1154548-26 ´z+VVr¶6¨ ´z+VVr¶6¨ Original instructions
Related manuals
Manual 24 pages 55.64 Kb

320 AWD, 318 specifications

The Husqvarna 318 and 315 are two remarkable models from Husqvarna, a brand renowned for its quality outdoor power equipment. These compact ride-on lawn mowers are designed to provide optimal performance, maneuverability, and versatility, making them ideal for both residential and commercial use.

One of the key features of the Husqvarna 318 and 315 is their efficient cutting system. Equipped with a high-performance cutting deck, these mowers deliver superior grass-cutting capabilities. The cutting height can be easily adjusted, allowing users to achieve the desired finish with precision. Additionally, the 18-inch cutting width is perfect for navigating tight spaces and corners, making these models suitable for intricate landscaping tasks.

Both models boast an innovative articulated steering system, which enhances their maneuverability. This feature allows the mower to pivot through tight turns, significantly reducing the risk of damage to flower beds and other landscaping features. The Husqvarna 318 and 315 also come with a compact design, making them easy to transport and store.

Equipped with powerful engines, the 318 and 315 provide dependable performance, ensuring that users can tackle even the most challenging lawn care tasks with ease. The engines are designed for fuel efficiency, allowing for longer run times and reduced emissions, aligning with contemporary environmental standards.

The ergonomic seat and intuitive controls provide comfort and convenience, ensuring that users can enjoy extended mowing sessions without discomfort. The dashboard features easy-to-read gauges and controls, making it simple for users to monitor performance and adjust settings on-the-go.

Husqvarna has incorporated cutting-edge technology into these models, including the Bluetooth-enabled connectivity feature. This allows users to track performance data and maintenance schedules directly from their mobile devices, promoting timely upkeep and efficiency.

In conclusion, the Husqvarna 318 and 315 ride-on lawn mowers are versatile and efficient choices for any lawn care enthusiast. With their high-performance cutting systems, innovative steering technology, and user-friendly design, these models are built to enhance the mowing experience. Whether for residential gardens or commercial properties, the Husqvarna 318 and 315 deliver outstanding results, setting a new standard in ride-on mower technology.
Top Page Image Contents