Husqvarna LTH2038 manual To Install Steering Wheel See Fig, Install Seat See Figs

Page 6

ASSEMBLY

TO INSTALL STEERING WHEEL (See Fig. 2)

ASSEMBLE EXTENSION SHAFT AND BOOT

Slide extension shaft onto lower steering shaft.

Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

Position front wheels of the tractor so they are pointing straight forward.

Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

Assemble large flat washer, lock washer, hex bolt and tighten securely.

Snap steering wheel insert into center of steering wheel.

Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

BOLT

LOCK

WASHER

LARGE FLAT

WASHER

STEERING

WHEEL

STEERING

BOOT

INSTALL SEAT (See Figs. 3 and 4)

Remove bolt and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor. Remove the cardboard packing and discard.

Connect switch to seat.

Place seat on seat pan so all three (3) bottom pads are positioned over large slotted holes in pan.

SEAT

SWITCH

PAD

SLOT

SEAT

PAN

TAPE

WIRING HARNESS

FIG. 3

Push down on seat to engage pads in slots and pull seat towards rear of tractor.

Raise seat and tighten bolt securely.

Remove tape and discard.

Lower seat into operating position and sit on seat. Press clutch/brake pedal all the way down. If operating position is not comfortable, adjust seat.

TO ADJUST SEAT (See Fig. 4):

Grasp adjustment handle and pull up, slide seat to desired position and release adjustment handle.

SLOT

TAPE

PAD

 

FLAT

 

WASHER

 

EXTENSION SHAFT

LOWER STEERING SHAFT

STEERING WHEEL ADAPTOR

SEAT PAN

 

BOLT

TAB

ADJUSTMENT

HANDLE

 

 

Fig. 4

NOTE: You may now roll your tractor off the skid. Follow the instructions below to remove the tractor from the skid.

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in

Fig. 2

front of tractor is clear of other people and objects.

6

Image 6
Contents LTH2038 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyTools Required for Assembly To Remove Tractor from CartonTo Adjust Seat See Fig To Install Steering Wheel See FigInstall Seat See Figs Assemble Extension Shaft and BootCheck Deck Levelness To Install Hood Scoop See FigCheck Tire Pressure Check Proper Position of ALL BeltsOperation Know Your Tractor To USE Throttle Control D See Fig HOW to USE Your TractorTo SET Parking Brake See Fig Stopping See FigTo Stop Mower Blades Service REMINDER/HOUR MeterTo Operate Mower To Operate on HillsTo Transport See Fig Before Starting the EngineReverse Operation System ROS Check Engine OIL LevelTo Start Engine See Fig Purge TransmissionAutomatic Transmission Warm UP Mowing Tips General Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningSpark Plugs Deck Washout Port See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Replace Motion Drive Belt See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check BrakeReplacing Battery See Fig To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig To Remove Wheel See FigTransmission Fuel System StorageOther Engine OILTroubleshooting Problem Cause CorrectionEngine continues Service Notes Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX06.21.10 CL