Husqvarna 2146XLS To Move Forward and Backward See Fig, To USE Cruise Control J See Fig

Page 10

OPERATION

TO MOVE FORWARD AND BACKWARD (See Fig. 7)

The direction and speed of movement is controlled by the forward and reverse drive pedals.

Start tractor and release parking brake.

Slowly depress forward (K) or reverse (L) drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.

K

J

L

FIG. 7

TO USE CRUISE CONTROL (J) (See Fig. 7)

The cruise control feature can be used for forward travel only.

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

Fig. 8

Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

Repeat for all, installing gauge wheel in same adjust- ment hole.

FIG. 9

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

Select desired height of cut (see "TO ADJUST MOWER CUTTING HEIGHT")

Start mower blades by engaging attachment clutch control.

10

Image 10
Contents 2146XLS General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyTools Required for Assembly ToremovetractorfromcartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor To SET Parking BRAKESee Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged Stopping See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigReverse Operation System ROS Service REMINDER/HOUR MeterTo Stop Mower Blades To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level Reserve Fuel Valve Operation See FigPurge Transmission Mowing TipsAutomatic Transmission Warm UP General Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine Muffler CleaningEngine Cooling System Spark PlugsTo Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig Raise attachment lift lever to highest position Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Check Brake To Remove Wheel for Repairs See FigTransmission Fuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic RelayTractor - Model Number 2146XLS 96043006700, Product no 43 Electrical KEY Part DescriptionChassis Tractor - Model Number 2146XLS 96043006700, Product no 43 Tractor - Model Number 2146XLS 96043006700, Product no 43 DriveNut U-CHNL 1/4-20 550DP .350 PNL Spark Arrester KIT EngineEngine Power Rating Information Steering Assembly Prem Husq SR532 41 Wheel, Steering 532 19 Seat Assembly 532 42 SeatMower Lift 113 100Mower Deck KEY Part NO. no Description Decals Wheels and TiresLimited Warranty Husqvarna S Obligations Under the Warranty 532 42 55-92 11.25.08 BAD

2146XLS specifications

The Husqvarna 2146XLS is a remarkable tool in the world of outdoor power equipment, particularly popular among homeowners and professionals seeking an efficient and versatile chainsaw. Engineered with precision and durability in mind, the 2146XLS offers a blend of power and user-friendly features that make it suitable for various cutting tasks, from light pruning to more demanding tree felling.

One of the standout features of the Husqvarna 2146XLS is its powerful engine. Equipped with a robust gasoline-powered engine, it delivers impressive performance while ensuring low fuel consumption. This means users can enjoy extended operating times without frequently refueling, making it an ideal choice for larger projects. Additionally, the engine’s design minimizes emissions, aligning with modern environmental standards.

The chainsaw features an easy-to-start system, which reduces the effort required to start the engine. This is particularly beneficial for users who may struggle with traditional pull-start mechanisms. The innovative design includes an adjustable oil pump that provides optimal lubrication to the chain, enhancing its performance and lifespan while also reducing the frequency of maintenance.

Another significant characteristic of the 2146XLS is its ergonomically designed handle. This thoughtful design emphasizes comfort and control, allowing users to maneuver the chainsaw effortlessly, even during extended use. The anti-vibration technology incorporated into the handle further enhances user comfort, reducing fatigue and enabling more precise cutting.

The chainsaw is equipped with a high-quality bar and chain, designed for excellent cutting performance and durability. The chain's sharpness and construction contribute to clean cuts, allowing users to finish their tasks quickly and efficiently. Moreover, the chainsaw's chain tensioning system is designed for convenience, enabling quick adjustments without the need for additional tools.

Safety is a primary consideration in the design of the Husqvarna 2146XLS. The chainsaw includes several safety features, such as an inertia-activated chain brake, which halts the chain in the event of kickback. Additionally, the front handguard protects the operator's hands during operation.

In summary, the Husqvarna 2146XLS stands out for its powerful engine, user-friendly features, comfort-focused design, and safety technologies. Whether for residential or professional use, this chainsaw provides the reliability and performance users need to tackle various cutting tasks with confidence and ease.