Husqvarna 2146XLS owner manual Cleaning, Engine Cooling System, Muffler, Spark Plugs

Page 17

MAINTENANCE

ENGINE COOLING SYSTEM

To ensure proper cooling, make sure the grass screen, cooling fins, and other external surfaces of the engine are kept clean at all times.

Every 100 hours of operation (more often under extremely dusty, dirty conditions), remove the blower housing and other cooling shrouds. Clean the cooling fins and external surfaces as necessary. Ensure the cooling shrouds are reinstalled.

NOTE: Operating the engine with a blocked grass screen, dirty or plugged cooling fins, and/or cooling shrouds removed will cause engine damage due to overheating.

MUFFLER

Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage.

SPARK PLUGS

Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in “PRODUCT SPECIFICATIONS” section of this manual.

IN-LINE FUEL FILTER (See Fig. 18)

The fuel filter should be replaced once each season. If fuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required.

•With engine cool, remove filter and plug fuel line sec- tions.

•Place new fuel filter in position in fuel line with arrow pointing towards carburetor.

•Be sure there are no fuel line leaks and clamps are properly positioned.

•Immediately wipe up any spilled gasoline.

CLAMP

FUEL FILTER

FIG. 18

CLEANING

•Clean engine, battery, seat, finish, etc. of all foreign matter.

•Keep finished surfaces and wheels free of all gasoline, oil, etc.

•Protect painted surfaces with automotive type wax.

We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and trans- mission are covered to keep water out. Water in engine or transmission will shorten the useful life of your tractor. Use compressed air or a leaf blower to remove grass, leaves and trash from tractor and mower.

DECK WASHOUT PORT (See Fig. 19)

Your tractor’s deck is equipped with a washout port on its surface as part of its deck wash system. It should be utilized after each use.

1.Drive the tractor to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to reach.

IMPORTANT: Make certain the tractor’s discharge chute is directed AWAY from your house, garage, parked cars, etc. Remove bagger chute or mulch cover if attached.

2.Make sure the PTO (Blade Engage) is not engaged, set the parking brake, and stop the engine.

3.Thread the nozzle adapter (packaged with your tractor’s Operator’s Manual) onto the end of your garden hose.

4.Pull back the lock collar of the nozzle adapter and push the adapter onto the deck washout port at the left end of the mower deck. Release the lock collar to lock the adapter on the nozzle.

HOSE

NOZZLE ADAPTER

WASHOUT

PORT

Fig. 19

IMPORTANT: Tug hose ensuring connection is secure.

5.Turn the water on.

6.While sitting in the operator’s position on the tractor, re-start the engine and place the throttle lever in the Fast " " position.

IMPORTANT: Recheck the area making certain the area is clear.

7.Move the tractor’s PTO (Blade Engage) to the ON position. Remain in the operator’s position with the cutting deck engaged until the deck is cleaned.

8.Move the tractor’s PTO (Blade Engage) to the OFF position. Turn the ignition key to the STOP position to turn the tractor’s engine off. Turn the water off.

9.Pull back the lock collar of the nozzle adapter to dis- connect the adapter from the nozzle washout port.

10.Move the tractor to a dry area, preferably a concrete or paved area. Engage the mower deck PTO to remove ex- cess water and to help dry before putting the tractor away.

WARNING: A broken or missing washout fitting could expose you or others to thrownobjectsfromcontactwiththeblade.

•Replace broken or missing washout fitting immediately, prior to using mower again.

•Pluganyholesinmowerwithboltsandlocknuts.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 2146XLS Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Tools Required for Assembly AssemblyUnassembled Parts ToremovetractorfromcartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Attachment Clutch Switch Disengaged Engaged HOW to USE Your TractorTo SET Parking BRAKESee Fig Stopping See FigTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigTo Move Forward and Backward See Fig To USE Cruise Control J See FigTo Stop Mower Blades Service REMINDER/HOUR MeterReverse Operation System ROS To Operate on HillsCheck Engine OIL Level Before Starting the EngineADD Gasoline Reserve Fuel Valve Operation See FigAutomatic Transmission Warm UP Mowing TipsPurge Transmission Maintenance MaintenanceGeneral Recommendations ScheduleTractor BatteryBlade Care Blade Removal See FigEngine Engine Cooling System CleaningMuffler Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Figs Raise attachment lift lever to highest position To Level Mower Visual SIDE-TO-SIDE Adjustment See FigTo Replace Motion Drive Belt See Fig To Replace Mower Blade Drive Belt See FigTo Check Brake To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTransmission Other StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Relay SchematicTractor - Model Number 2146XLS 96043006700, Product no 43 KEY Part Description ElectricalChassis Tractor - Model Number 2146XLS 96043006700, Product no 43 Drive Tractor - Model Number 2146XLS 96043006700, Product no 43Nut U-CHNL 1/4-20 550DP .350 PNL Engine Spark Arrester KITEngine Power Rating Information Prem Husq SR Steering Assembly532 41 Wheel, Steering 532 19 532 42 Seat Seat Assembly113 100 Mower LiftMower Deck KEY Part NO. no Description Wheels and Tires DecalsLimited Warranty Husqvarna S Obligations Under the Warranty 532 42 55-92 11.25.08 BAD

2146XLS specifications

The Husqvarna 2146XLS is a remarkable tool in the world of outdoor power equipment, particularly popular among homeowners and professionals seeking an efficient and versatile chainsaw. Engineered with precision and durability in mind, the 2146XLS offers a blend of power and user-friendly features that make it suitable for various cutting tasks, from light pruning to more demanding tree felling.

One of the standout features of the Husqvarna 2146XLS is its powerful engine. Equipped with a robust gasoline-powered engine, it delivers impressive performance while ensuring low fuel consumption. This means users can enjoy extended operating times without frequently refueling, making it an ideal choice for larger projects. Additionally, the engine’s design minimizes emissions, aligning with modern environmental standards.

The chainsaw features an easy-to-start system, which reduces the effort required to start the engine. This is particularly beneficial for users who may struggle with traditional pull-start mechanisms. The innovative design includes an adjustable oil pump that provides optimal lubrication to the chain, enhancing its performance and lifespan while also reducing the frequency of maintenance.

Another significant characteristic of the 2146XLS is its ergonomically designed handle. This thoughtful design emphasizes comfort and control, allowing users to maneuver the chainsaw effortlessly, even during extended use. The anti-vibration technology incorporated into the handle further enhances user comfort, reducing fatigue and enabling more precise cutting.

The chainsaw is equipped with a high-quality bar and chain, designed for excellent cutting performance and durability. The chain's sharpness and construction contribute to clean cuts, allowing users to finish their tasks quickly and efficiently. Moreover, the chainsaw's chain tensioning system is designed for convenience, enabling quick adjustments without the need for additional tools.

Safety is a primary consideration in the design of the Husqvarna 2146XLS. The chainsaw includes several safety features, such as an inertia-activated chain brake, which halts the chain in the event of kickback. Additionally, the front handguard protects the operator's hands during operation.

In summary, the Husqvarna 2146XLS stands out for its powerful engine, user-friendly features, comfort-focused design, and safety technologies. Whether for residential or professional use, this chainsaw provides the reliability and performance users need to tackle various cutting tasks with confidence and ease.
Top Page Image Contents