Husqvarna 2146XLS To Check Brake, Front Wheel TOE-IN/CAMBER, To Remove Wheel for Repairs See Fig

Page 22

SERVICE AND ADJUSTMENTS

TO CHECK BRAKE

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced.

You may also check brake by:

•Park tractor on a level, dry concrete or paved surface, depress brake pedal all the way down and engage parking brake.

•Disengage transmission by placing freewheel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manu- ally push the tractor forward. If the rear wheels rotate, then the brake needs to be serviced. Contact a qualified service center.

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 32)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 32

TO START ENGINE WITH A WEAK BATTERY (See Fig. 33)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

WEAK OR

FULLY CHARGED

DEAD BATTERY

BATTERY

FIG. 33

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents 2146XLS General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyTools Required for Assembly ToremovetractorfromcartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor To SET Parking BRAKESee Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged Stopping See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigReverse Operation System ROS Service REMINDER/HOUR MeterTo Stop Mower Blades To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level Reserve Fuel Valve Operation See FigPurge Transmission Mowing TipsAutomatic Transmission Warm UP General Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine Muffler CleaningEngine Cooling System Spark PlugsTo Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig Raise attachment lift lever to highest position Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Check Brake To Remove Wheel for Repairs See FigTransmission Fuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic RelayTractor - Model Number 2146XLS 96043006700, Product no 43 Electrical KEY Part DescriptionChassis Tractor - Model Number 2146XLS 96043006700, Product no 43 Tractor - Model Number 2146XLS 96043006700, Product no 43 DriveNut U-CHNL 1/4-20 550DP .350 PNL Spark Arrester KIT EngineEngine Power Rating Information Steering Assembly Prem Husq SR532 41 Wheel, Steering 532 19 Seat Assembly 532 42 SeatMower Lift 113 100Mower Deck KEY Part NO. no Description Decals Wheels and TiresLimited Warranty Husqvarna S Obligations Under the Warranty 532 42 55-92 11.25.08 BAD

2146XLS specifications

The Husqvarna 2146XLS is a remarkable tool in the world of outdoor power equipment, particularly popular among homeowners and professionals seeking an efficient and versatile chainsaw. Engineered with precision and durability in mind, the 2146XLS offers a blend of power and user-friendly features that make it suitable for various cutting tasks, from light pruning to more demanding tree felling.

One of the standout features of the Husqvarna 2146XLS is its powerful engine. Equipped with a robust gasoline-powered engine, it delivers impressive performance while ensuring low fuel consumption. This means users can enjoy extended operating times without frequently refueling, making it an ideal choice for larger projects. Additionally, the engine’s design minimizes emissions, aligning with modern environmental standards.

The chainsaw features an easy-to-start system, which reduces the effort required to start the engine. This is particularly beneficial for users who may struggle with traditional pull-start mechanisms. The innovative design includes an adjustable oil pump that provides optimal lubrication to the chain, enhancing its performance and lifespan while also reducing the frequency of maintenance.

Another significant characteristic of the 2146XLS is its ergonomically designed handle. This thoughtful design emphasizes comfort and control, allowing users to maneuver the chainsaw effortlessly, even during extended use. The anti-vibration technology incorporated into the handle further enhances user comfort, reducing fatigue and enabling more precise cutting.

The chainsaw is equipped with a high-quality bar and chain, designed for excellent cutting performance and durability. The chain's sharpness and construction contribute to clean cuts, allowing users to finish their tasks quickly and efficiently. Moreover, the chainsaw's chain tensioning system is designed for convenience, enabling quick adjustments without the need for additional tools.

Safety is a primary consideration in the design of the Husqvarna 2146XLS. The chainsaw includes several safety features, such as an inertia-activated chain brake, which halts the chain in the event of kickback. Additionally, the front handguard protects the operator's hands during operation.

In summary, the Husqvarna 2146XLS stands out for its powerful engine, user-friendly features, comfort-focused design, and safety technologies. Whether for residential or professional use, this chainsaw provides the reliability and performance users need to tackle various cutting tasks with confidence and ease.
Top Page Image Contents