Husqvarna 2146XLS owner manual Tractor, Blade Care, Blade Removal See Fig, Battery

Page 15

MAINTENANCE

TRACTOR

Always observe safety rules when performing any maintenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See the sides of tires for proper PSI).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS) (See Fig. 14)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

 

 

 

 

 

 

 

 

 

 

02828

ROS "ON"

ENGINE "ON" POSITION

POSITION

(NORMAL OPERATING)

 

 

 

 

 

 

Fig. 14

15

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

CAUTION: Use only a replacement blade ap- proved by the manufacturer of your tractor. Using a blade not approved by the manu- facturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 15)

•Raisemowertohighestpositiontoallowaccesstoblades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new or resharpened blade with stamped "THIS SIDE UP" facing deck and mandrel assembly.

IMPORTANT:TOENSUREPROPERASSEMBLY,CENTERHOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.

MANDREL ASSEMBLY

 

BLADE

BLADE BOLT

STAR

(SPECIAL)

CENTER HOLE

Fig. 15

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE:Theoriginalequipmentbatteryonyourtractorismain- tenance free. Do not attempt to open or remove caps or cov- ers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

•Raise seat.

•Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor.

•Rinse the battery with plain water and dry.

•Clean terminals and battery cable ends with wire brush until bright.

•Coat terminals with grease or petroleum jelly.

•Reinstall battery (See “REPLACING BATTERY" in the SERVICEANDADJUSTMENTSsectionofthismanual).

Page 14 Page 16
Image 15
Page 14 Page 16
Contents 2146XLS II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Toremovetractorfromcarton AssemblyTools Required for Assembly Unassembled PartsCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor Stopping See Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged To SET Parking BRAKESee FigTo USE Cruise Control J See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Move Forward and Backward See FigTo Operate on Hills Service REMINDER/HOUR MeterTo Stop Mower Blades Reverse Operation System ROSReserve Fuel Valve Operation See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Schedule MaintenanceMaintenance General RecommendationsBlade Removal See Fig BatteryTractor Blade CareEngine Spark Plugs CleaningEngine Cooling System MufflerService and Adjustments To Install Mower See FigsTo Remove Mower See Fig Raise attachment lift lever to highest position To Level Mower Visual SIDE-TO-SIDE Adjustment See FigTo Replace Motion Drive Belt See Fig To Replace Mower Blade Drive Belt See FigTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigTo Check Brake Front Wheel TOE-IN/CAMBERTransmission Engine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Relay SchematicTractor - Model Number 2146XLS 96043006700, Product no 43 KEY Part Description ElectricalChassis Tractor - Model Number 2146XLS 96043006700, Product no 43 Drive Tractor - Model Number 2146XLS 96043006700, Product no 43Nut U-CHNL 1/4-20 550DP .350 PNL Engine Spark Arrester KITEngine Power Rating Information Prem Husq SR Steering Assembly532 41 Wheel, Steering 532 19 532 42 Seat Seat Assembly113 100 Mower LiftMower Deck KEY Part NO. no Description Wheels and Tires DecalsLimited Warranty Husqvarna S Obligations Under the Warranty 532 42 55-92 11.25.08 BAD

2146XLS specifications

The Husqvarna 2146XLS is a remarkable tool in the world of outdoor power equipment, particularly popular among homeowners and professionals seeking an efficient and versatile chainsaw. Engineered with precision and durability in mind, the 2146XLS offers a blend of power and user-friendly features that make it suitable for various cutting tasks, from light pruning to more demanding tree felling.

One of the standout features of the Husqvarna 2146XLS is its powerful engine. Equipped with a robust gasoline-powered engine, it delivers impressive performance while ensuring low fuel consumption. This means users can enjoy extended operating times without frequently refueling, making it an ideal choice for larger projects. Additionally, the engine’s design minimizes emissions, aligning with modern environmental standards.

The chainsaw features an easy-to-start system, which reduces the effort required to start the engine. This is particularly beneficial for users who may struggle with traditional pull-start mechanisms. The innovative design includes an adjustable oil pump that provides optimal lubrication to the chain, enhancing its performance and lifespan while also reducing the frequency of maintenance.

Another significant characteristic of the 2146XLS is its ergonomically designed handle. This thoughtful design emphasizes comfort and control, allowing users to maneuver the chainsaw effortlessly, even during extended use. The anti-vibration technology incorporated into the handle further enhances user comfort, reducing fatigue and enabling more precise cutting.

The chainsaw is equipped with a high-quality bar and chain, designed for excellent cutting performance and durability. The chain's sharpness and construction contribute to clean cuts, allowing users to finish their tasks quickly and efficiently. Moreover, the chainsaw's chain tensioning system is designed for convenience, enabling quick adjustments without the need for additional tools.

Safety is a primary consideration in the design of the Husqvarna 2146XLS. The chainsaw includes several safety features, such as an inertia-activated chain brake, which halts the chain in the event of kickback. Additionally, the front handguard protects the operator's hands during operation.

In summary, the Husqvarna 2146XLS stands out for its powerful engine, user-friendly features, comfort-focused design, and safety technologies. Whether for residential or professional use, this chainsaw provides the reliability and performance users need to tackle various cutting tasks with confidence and ease.
Top Page Image Contents