Husqvarna 2146XLS owner manual Before Starting the Engine, Check Engine OIL Level, ADD Gasoline

Page 12

OPERATION

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Maintenance section of this manual).

•To change engine oil, see the Maintenance section in this manual.

ADD GASOLINE

•Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW 32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP ENSURE GOOD COLD WEATHER STARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

RESERVE FUEL VALVE OPERATION (See Fig. 12)

1.Raise seat to access reserve fuel valve.

2.In normal operation, valve should be set to primary (as shown in view)

3.If tractor runs out of fuel, rotate valve handle to reserve.

4.Drive tractor to be refueled.

5.After refueling, return valve to primary position.

RESERVE

FUEL VALVE

RESERVE

PRIMARY

Fig. 12

TO START ENGINE (See Fig. 3)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Be sure freewheel control is in the transmission engaged position.

•Sit on seat in operating position, depress brake pedal and set parking brake.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to choke position.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke position and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, move the throttle control to the fast position.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50° F and below)

•When engine starts, allow engine to run with the throttle control in the choke position until the engine runs roughly, then move throttle control to fast posi- tion. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents 2146XLS Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Assembly Tools Required for AssemblyUnassembled Parts ToremovetractorfromcartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Attachment Clutch Switch Disengaged EngagedTo SET Parking BRAKESee Fig Stopping See FigTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigTo Move Forward and Backward See Fig To USE Cruise Control J See FigService REMINDER/HOUR Meter To Stop Mower BladesReverse Operation System ROS To Operate on HillsBefore Starting the Engine Check Engine OIL LevelADD Gasoline Reserve Fuel Valve Operation See FigMowing Tips Purge TransmissionAutomatic Transmission Warm UP Maintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBlade Care Blade Removal See FigEngine Cleaning Engine Cooling SystemMuffler Spark PlugsService and Adjustments To Install Mower See FigsTo Remove Mower See Fig Raise attachment lift lever to highest position Visual SIDE-TO-SIDE Adjustment See Fig To Level MowerTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig To Check BrakeFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTransmission Storage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic RelayTractor - Model Number 2146XLS 96043006700, Product no 43 Electrical KEY Part DescriptionChassis Tractor - Model Number 2146XLS 96043006700, Product no 43 Tractor - Model Number 2146XLS 96043006700, Product no 43 DriveNut U-CHNL 1/4-20 550DP .350 PNL Spark Arrester KIT EngineEngine Power Rating Information Steering Assembly Prem Husq SR532 41 Wheel, Steering 532 19 Seat Assembly 532 42 SeatMower Lift 113 100Mower Deck KEY Part NO. no Description Decals Wheels and TiresLimited Warranty Husqvarna S Obligations Under the Warranty 532 42 55-92 11.25.08 BAD

2146XLS specifications

The Husqvarna 2146XLS is a remarkable tool in the world of outdoor power equipment, particularly popular among homeowners and professionals seeking an efficient and versatile chainsaw. Engineered with precision and durability in mind, the 2146XLS offers a blend of power and user-friendly features that make it suitable for various cutting tasks, from light pruning to more demanding tree felling.

One of the standout features of the Husqvarna 2146XLS is its powerful engine. Equipped with a robust gasoline-powered engine, it delivers impressive performance while ensuring low fuel consumption. This means users can enjoy extended operating times without frequently refueling, making it an ideal choice for larger projects. Additionally, the engine’s design minimizes emissions, aligning with modern environmental standards.

The chainsaw features an easy-to-start system, which reduces the effort required to start the engine. This is particularly beneficial for users who may struggle with traditional pull-start mechanisms. The innovative design includes an adjustable oil pump that provides optimal lubrication to the chain, enhancing its performance and lifespan while also reducing the frequency of maintenance.

Another significant characteristic of the 2146XLS is its ergonomically designed handle. This thoughtful design emphasizes comfort and control, allowing users to maneuver the chainsaw effortlessly, even during extended use. The anti-vibration technology incorporated into the handle further enhances user comfort, reducing fatigue and enabling more precise cutting.

The chainsaw is equipped with a high-quality bar and chain, designed for excellent cutting performance and durability. The chain's sharpness and construction contribute to clean cuts, allowing users to finish their tasks quickly and efficiently. Moreover, the chainsaw's chain tensioning system is designed for convenience, enabling quick adjustments without the need for additional tools.

Safety is a primary consideration in the design of the Husqvarna 2146XLS. The chainsaw includes several safety features, such as an inertia-activated chain brake, which halts the chain in the event of kickback. Additionally, the front handguard protects the operator's hands during operation.

In summary, the Husqvarna 2146XLS stands out for its powerful engine, user-friendly features, comfort-focused design, and safety technologies. Whether for residential or professional use, this chainsaw provides the reliability and performance users need to tackle various cutting tasks with confidence and ease.
Top Page Image Contents