Husqvarna 2042 LS (CA) To Move Forward and Backward See Fig, To USE Cruise Control J See Fig

Page 11

OPERATION

TO MOVE FORWARD AND BACKWARD (See Fig. 7)

The direction and speed of movement is controlled by the forward and reverse drive pedals.

•Start tractor and release parking brake.

•Slowly depress forward (K) or reverse (L) drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.

J

K

L

FIG. 7

TO USE CRUISE CONTROL - J (See Fig. 7)

The cruise control feature can be used for forward travel only.

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

FIG. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

FIG.9

TO OPERATE MOWER (See Fig. 10)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

1.Select desired height of cut with attachment lift lever.

2.Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

10

Page 10 Page 12
Image 11
Page 10 Page 12
Contents LS CA Page II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceIII. Children Table of Contents Unpack Carton AssemblyUnassembled Parts To Remove Tractor from CartonCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor To USE Throttle Control D See Fig HOW to USE Your TractorTo SET Parking BRAKESee Fig Stopping See FigTo USE Cruise Control J See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Move Forward and Backward See FigTo Transport See Figs Using the Reverse Operation SystemReverse Operation System ROS To Operate on HillsADD Gasoline Service REMINDER/HOUR MeterBefore Starting the Engine Check Engine OIL LevelPurge Transmission Mowing TipsLubrication Chart MaintenanceBlade Care TractorBrake Operation TiresEngine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Service and Adjustments To Level Mower To Replace Motion Drive Belt See Fig To Replace Mower Drive Belt See FigTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigTo Check Brake Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Points Engine dies when SCH12 SchematicElectrical KEY Part Description Chassis Tractor - Model Number 2042LS 96043004800, Product no 43 Drive Tractor - Model Number 2042LS 96043004800, Product no 43 28 90 Spark Arrester KITEngine Engine Power Rating Information Steering Assembly 532 41 Wheel, Steering 532 18 532 40 Seat Seat AssemblyWheels and Tires Decals188 189 6188 145116 190 118Mower Deck 100 Mower LiftSuggested Guide for Sighting Slopes for Safe Operation 532 41 88-19 12-12-07 SBW Warranty Statement

2042 LS (CA) specifications

The Husqvarna 2042 LS (CA) is a lawnmower designed for both efficiency and user convenience, making it an ideal choice for homeowners looking to maintain a pristine lawn. This model combines powerful performance with innovative technology, ensuring a superior mowing experience.

One of the standout features of the Husqvarna 2042 LS is its impressive cutting deck. With a 42-inch cutting width, it allows for the swift trimming of lawns while maintaining the ability to navigate various terrains with ease. The cutting deck is designed for optimal airflow, enhancing grass clipping distribution for a neater finish. The mower also comes equipped with a robust steel chassis that promotes durability and longevity.

Powering the Husqvarna 2042 LS is a reliable and potent engine, providing the necessary torque to tackle different grass types and terrain obstacles. This ensures that the mower can effortlessly handle thicker grass without stalling, catering to diverse lawn conditions. The intuitive starting system allows for easy ignition, so users can quickly get to work without frustration.

Another notable characteristic is the advanced cutting height adjustment system. This feature allows users to easily select their preferred cutting height, enhancing flexibility for different seasons or grass types. Whether one wants a short trim during the summer or a slightly longer cut in the spring, the 2042 LS accommodates these needs with multiple height settings.

User comfort is prioritized with the ergonomic design of the mower. The handles are adjustable and designed to reduce fatigue during extended use. Additionally, the tractor-style layout provides better visibility, ensuring that users can easily monitor their mowing path.

The Husqvarna 2042 LS stands out due to its commitment to technology as well. The mower incorporates features such as a dashboard display that provides important information like fuel levels and service reminders, ensuring that users are always informed about machine performance.

Fuel efficiency is another hallmark of this lawnmower, minimizing trips to the gas station and maximizing cutting time. Combined with low emissions, the Husqvarna 2042 LS (CA) is an environmentally friendly option.

In conclusion, the Husqvarna 2042 LS (CA) is a powerful, versatile lawnmower that combines efficiency, user-friendly features, and innovative technology. Its durable design, advanced cutting systems, and comfort-oriented attributes make it an excellent investment for any homeowner looking to enhance their lawn care experience.
Top Page Image Contents