Husqvarna J 55S L Maintenance, Wartung, Entretien, Inspeccion, Onderhoud, Mateniméto, Regularly

Page 17

Maintenance

Always remove the spark plug lead before repair, cleaning or maintenance work. After 5 hours running time, tighten screws and nuts. Check the oil. The spark plug must be at the highest point on the mower when it is tilted up.

Wartung

Ziehen Sie immer das Zündkerzenkabel ab, bevor Sie mit der Reparatur, Reinigung oder mit Wartungsarbeiten beginnen. Nach den ersten 5 Betreibstunden alle Schrauben und Muttern überprüfen. Ölstand kontrollieren. Wenn der Rasenmäher gekippt wird, müssen sich die Zündkerze an der höchsten Stelle befinden.

Entretien

Toujours debrancher la bougie avant réparation nettoyage entretien. Après 5 heures d'utilisation, resserrer vis et écrous. Vérifier l'huile. Lorsque la tondeuse est inclinée sur le côtc, il faut que la bougie occupent la position la plus élevée.

Inspeccion

Desconéctese siempre el cable del encendido de la bujíaantes de hacer una reparación, limpieza o trabajo de mantenimiento. Vovler a apretar tuercas y tornillos después de cinco horas de trabajo. Contrólose el aceite. Si se coloca el cortacésped de lado, el punto más alto debe ser la bujía.

Onderhoud

Voordag u begint met schoonmaken, reparaties of afstellen, altijd eerst de bougiekabel losmaken. Bouten en moeren kontroleren ma vijf draaiuren. Oliepeil kontroleren en zonodig bijvullen. Als de maaier op de zijkant wordt gelegd, zorg dan dat de bougie naar boven zign gericht.

Mateniméto

Manutenzione: Staccare sempre il cavo di accensione prima di riparazioni, pulizie o lavori di menutenzione. Dopo 5 ore di funzionamento stringere viti e dadi. Controllare l'olio. Piegando la falciatrice sul fiancolare attenzione che la candela sia il punto più alto.

Regularly

Stop the engine and unscrew the dipstick. The level should be between FULL and ADD. NOTE: the dipstick must be screwed all the way down in order to indicate correct oil level. Avoid filling with too much oil.

Regelmässig

Stellen Sie den Motor ab und schrauben Sie den Ölpeilstab heraus. De Ölstand soll swischen FULL and ADD liegen. ACH- TUNG: der Ölpeilstab muss vollständig hineingeschraubt sein, damit der richtige Ölstand angezeigt werden kann. Vermeiden Sie zu viel Öl einzufüllen.

Régulièrement

Arrêter le moteur et vérifier la jauge à julie. Le niveau doit être situé entre FULL (plein) et ADD (ajoutez). ATTENTION: il faut que la jauge soit vissé à fond pour obtenir un résultat correct. Evitez de mettre trop d'huile.

Periódicamente

Parar el motor para controlar el nivel de aceite del motor. Debe estar entre FULL y ADD. ATENCIÓN: la tapa tiene que estar bien puesta para que la indicación del nivel de aceite de la varilla sea correcta. Evitar relleno excesivo de aceite.

Regelmatig

Kontroleer het oliepeil bij voorkeur bij een koude motor. Het niveau moet tussen FULL en ADD staan. Nooit beneden de ADD mar ook nooit boven FULL. N.B. De peilstok moet geheel ingedraaid worden voor dejuiste meting. Niet teveel olie bijvullen.

Periodicamente

Arrestare il more e controllare l'asta dell'olio. Ll livello deve trovarsi fra FULL e ADD. ATTENZIONE: l'asta dell'olio deve essere avvitata fino in fondo per vedere il livello correctto dell'olio. Evitare di versare troppo olio.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents 55S L Contents Indice Training IV. Maintenance and StorageII. Preparation III. OperationII. Vorbereitung SchulungIII. Betrieb IV. Wartung und LagerungII. Préparation Précautions d’utilisationIII. Utilisation IV. Entretien et EntreposageII. Preparación InstrucciónIII. Operación IV. Mantenimiento y AlmacenamientoII. Voorbereiding Veilig werken met handbediende grasmaaimachinesIII. Bediening IV. Onderhoud en OpslagII. Preparazione Addestramento All’usoIII. Funzionamento IV. Manutenzione e Periodi di Inattivita’190 Page Installez le protecteur de pieds arrière Install Rear Foot GuardHandle GriffTo Convert Mower Ajuste AdjustmentUmrüsten des Mäweks Pour Convertir la TondeuseFilling with Oil AjusteÖlaffülling Remplissage d’huileStart und Stopp Starting and StoppingMarche et Arrêt Arranque y ParadaDrive Mise en serviceLauf FuncionamientoGebrauch MAX UseUtilisation AplicacionWartung MaintenanceEntretien InspeccionJährlich nach Beendigung der Saison Annually After end of seasonAnnuellement à fin de la saison Revisión anual Al terminar la estaciónTransporte TransportVervoer Transporto532 41 90-73 Rev Printed 10.17.08 TH/TH/BY/BY/BY U.S.A

J 55S L specifications

The Husqvarna J 55S L is a versatile and powerful chainsaw designed for both professional and semi-professional users. It stands out in the Husqvarna range with a combination of user-friendly design, cutting-edge technology, and impressive performance, making it an excellent choice for tasks such as tree felling, limbing, and cutting firewood.

One of the key features of the J 55S L is its robust 55cc engine, which delivers a remarkable output, enabling operators to handle a variety of cutting applications with ease. This powerful engine is complemented by Husqvarna's X-Torq technology, which reduces fuel consumption and emissions without sacrificing performance. This environmentally friendly aspect makes the J 55S L not only efficient but also compliant with modern regulatory standards.

The chainsaw is equipped with an efficient cooling system that helps maintain optimal operating temperatures, extending the life of the engine and improving performance during prolonged use. Additionally, the J 55S L features an adjustable oil pump, allowing users to customize the chain lubricating system according to their specific needs. This ensures optimal chain lubrication, thereby enhancing cutting efficiency and prolonging the life of the chain and bar.

User comfort and safety are paramount in the design of the Husqvarna J 55S L. The chainsaw comes with a low-vibration system that significantly reduces vibrations transmitted to the user's hands and arms, minimizing fatigue during extended use. It also features an ergonomic handle design with a soft grip, which further enhances comfort while providing reliable control.

Furthermore, the tool's quick-release air filter facilitates easy maintenance, ensuring that users can keep the chainsaw in peak operating condition without excessive downtime. The chainsaw is also designed with an easy-to-access chain tensioning system, allowing for quick adjustments on the go.

In summary, the Husqvarna J 55S L combines powerful performance, innovative technologies, and user-centric design to create a chainsaw that meets the demands of both professional and casual users. Its balance of power, efficiency, and comfort ensures that it can handle a wide range of cutting tasks effectively, making it a solid investment for anyone in need of a reliable chainsaw. With its proven durability and advanced features, the J 55S L is a standout choice in the competitive chainsaw market.
Top Page Image Contents