Husqvarna GT2254 owner manual To Replace Mower Drive Belt See Fig, Belt Routing

Page 22

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER DRIVE BELT (See Fig. 23)

MOWER DRIVE BELT REMOVAL

•Park tractor on a level surface. Engage parking brake.

•Lower attachment lift lever to its lowest position.

•Disengage belt tension rod from lock bracket.

CAUTION: Belt tension rod is spring loaded. Have a ﬁrm grip on rod and release slowly.

•Remove screws from R.H. and L.H. mandrel covers and remove covers.

•Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.

MOWER DRIVE BELT INSTALLATION

•Install belt around both mandrel pulleys and around idler pulleys as shown.

•Install belt onto electric clutch pulley.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

•Reassemble R.H. and L.H. mandrel covers. Securely tighten all screws.

•Engage belt tension rod on locking bracket.

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

•Raise attachment lift lever to highest position.

•Remove belt from electric clutch pulley, both mandrel pulleys and all idler pulleys.

BELT ROUTING

	L.H. MANDREL
	COVER
	LOCKING BRACKET
BELT TENSION	ELECTRIC
ROD (DISENGAGED	ELECTRIC
POSITION)	CLUTCH
	PULLEY

R.H. MANDREL

COVER

R.H.

MANDREL

IDLER

PULLEYS

FIG. 23

22

Image 22

Contents GT2254 General Operation Safe Operation Practices for Ride-On MowersII. Slope Operation III. Children ServiceGeneral Service IV. TowingTable of Contents Seat Unassembled PartsSteering Wheel Gauge Wheels Slope SheetTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidInstall Seat See Fig Assemble Gauge Wheels to Mower Deck SeeInstall Mower and Drive Belt Sees Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Height Adjustment Knob Used to adjust the mower height Know Your TractorHOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigUsing the Reverse Operation System Reverse Operation System ROSBefore Starting the Engine Mowing Tips General Recommendations MaintenanceLubrication Chart Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Belts BatteryEngine Transaxle CoolingCleaning To Level Mower Housing Service and AdjustmentsTo Install Mower To Remove Mower See FigFRONT-TO-BACK Adjustment See Figs To Replace Mower Drive Belt See Fig Belt RoutingTo Check and Adjust Brake See Fig To Adjust Attachment Clutch See FigTo Replace Motion Drive Belt See Fig To Start Engine with a Weak Battery See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace FuseEngine OIL OtherFuel System CylindersTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor - Model NO. GT2254 96023000500 Product no 23Electrical 532 14 Battery KEY Part DescriptionChassis and Enclosures 167Repair Parts Ground Drive Repair Parts Steering Assembly 532 19 Wheel, Steering Engine Engine Briggs, Model No H777Order parts from engine Seat Assembly 532 19 SeatDecals Wheels & TiresLift Assembly Repair Parts Mower Deck Repair Parts Gear Drive Transaxle 532 00 Needle Bearing Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement Limited Warranty532 19 61-68 Rev 05.16.05 TR