Husqvarna GT2254 owner manual Install Seat See Fig, Assemble Gauge Wheels to Mower Deck See

Page 7

ASSEMBLY

INSTALL SEAT (See Fig. 3)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

SEAT

SEAT PAN

SHOULDER

BOLT

FLAT WASHER

ADJUSTMENT

02464

KNOB

 

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place gearshift lever in neutral (N) position.

•Roll tractor forward off skid.

TO DRIVETRACTOR OFF SKID (See Operation section for location and function of con- trols)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place gear shift lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine.After engine has started, move throttle control to idle position.

•Depress clutch/brake pedal into full "BRAKE" position and hold. Move gearshift lever to 1st gear.

•Slowly release clutch/brake pedal and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place gearshift lever in neutral position.

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

ASSEMBLE GAUGE WHEELS TO MOWER DECK (See Fig. 4 and 5)

The gauge wheels are designed to keep the mower deck in proper position when operating mower.

•Slide gauge wheel bar down into bracket channel, Be sure that gauge wheel bar aligning holes are on top. Assemble gauge wheels as shown using shoulder bolts, 3/8 washers and 3/8-16 center locknuts and tighten securely.

•For ease of mower to tractor assembly, set all the gauge wheels in the fourth hole from top. Retain with clevis pins and spring retainers.

RETAINER SPRING

PIN

 

SHOULDER

 

BOLT

 

ADJUSTING

 

BAR

 

GAUGE

 

WHEEL

3/8-16 CENTER

 

3/8 WASHER

LOCKNUT

 

FIG. 4

SET ALL WHEELS

TO 4TH HOLE

FROM TOP

FIG. 5

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents GT2254 General Operation Safe Operation Practices for Ride-On MowersII. Slope Operation IV. Towing ServiceGeneral Service III. ChildrenTable of Contents Slope Sheet Unassembled PartsSteering Wheel Gauge Wheels SeatBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Install Seat See FigInstall Mower and Drive Belt Sees Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor Height Adjustment Knob Used to adjust the mower heightHOW to USE Your Tractor Reverse Operation System ROS To Adjust Gauge Wheels See FigUsing the Reverse Operation System To Operate Mower See FigBefore Starting the Engine Mowing Tips Before Each USE MaintenanceLubrication Chart General RecommendationsBlade Removal See Fig TractorTo Sharpen Blade See Fig Transaxle Cooling BatteryEngine BeltsCleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower To Level Mower HousingFRONT-TO-BACK Adjustment See Figs Belt Routing To Replace Mower Drive Belt See FigTo Check and Adjust Brake See Fig To Adjust Attachment Clutch See FigTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigTo Replace Fuse To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorCylinders OtherFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Tractor - Model NO. GT2254 96023000500 Product no 23 SchematicElectrical KEY Part Description 532 14 Battery167 Chassis and EnclosuresRepair Parts Ground Drive Repair Parts Steering Assembly 532 19 Wheel, Steering Engine Engine Briggs, Model No H777Order parts from engine 532 19 Seat Seat AssemblyWheels & Tires DecalsLift Assembly Repair Parts Mower Deck Repair Parts Gear Drive Transaxle 532 00 Needle Bearing Service Notes Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationLimited Warranty Warranty Statement532 19 61-68 Rev 05.16.05 TR
Top Page Image Contents