Husqvarna GT2254 owner manual Engine dies when

Page 28

TROUBLESHOOTING POINTS

PROBLEM

CAUSE

 

CORRECTION

 

 

 

 

 

Engine dies when

1.

Reverse operation system

1.

Turn ignition key to

tractor is shifted

 

(ROS) is not "ON" while

 

ROS "ON" position.

into reverse

 

mower or other attachment

 

See Operation section.

 

 

is engaged.

 

 

 

 

 

 

 

Engine continues to run

1.

Faulty operator-safety presence control system.

1.

Check wiring, switches and connections. If not

when operator leaves seat

 

 

 

corrected, contact an authorized service center/

with attachment clutch

 

 

 

department.

engaged

 

 

 

 

 

 

 

 

 

Poor cut - uneven

1.

Worn, bent or loose blade.

1.

Replace blade. Tighten blade bolt.

 

2.

Mower deck not level.

2.

Level mower deck.

 

3.

Buildup of grass, leaves, and trash under mower.

3.

Clean underside of mower housing.

 

4.

Bent blade mandrel.

4.

Replace blade mandrel.

 

5.

Clogged mower deck vent holes from buildup of

5.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Mower blades will not

1.

Obstruction in clutch mechanism.

1.

Remove obstruction.

rotate

2.

Worn/damaged mower drive belt.

2.

Replace mower drive belt.

 

3.

Frozen idler pulley.

3.

Replace idler pulley.

 

4.

Frozen blade mandrel.

4.

Replace blade mandrel.

 

 

 

 

 

Poor grass discharge

1.

Engine speed too slow.

1.

Place throttle control in “FAST” position.

 

2.

Travel speed too fast.

2.

Shift to slower speed.

 

3.

Wet grass.

3.

Allow grass to dry before mowing.

 

4.

Mower deck not level.

4.

Level mower deck.

 

5.

Low/uneven tire air pressure.

5.

Check tires for proper air pressure.

 

6.

Worn, bent or loose blade.

6.

Replace/sharpen blade. Tighten blade bolt.

 

7.

Buildup of grass, leaves and trash under mower.

7.

Clean underside of mower housing.

 

8.

Mower drive belt worn.

8.

Replace mower drive belt.

 

9.

Blades improperly installed.

9.

Reinstall blades sharp edge down.

 

10.

Improper blades used.

10.

Replace with blades listed in this manual.

 

11.

Clogged mower deck vent holes from buildup of

11.

Clean around mandrels to open vent holes.

 

 

grass, leaves, and trash around mandrels.

 

 

 

 

 

 

 

Headlight(s) not working

1.

Light switch is “OFF”.

1.

Turn light switch “ON”.

(if so equipped)

2.

Bulb(s) or lamp(s) burned out.

2.

Replace bulb(s) or lamp(s).

 

3.

Faulty light switch.

3.

Check/replace light switch.

 

4.

Loose or damaged wiring.

4.

Check wiring and connections.

 

5.

Blown fuse.

5.

Replace fuse.

 

 

 

 

 

Battery will not charge

1.

Bad battery cell(s).

1.

Replace battery.

 

2.

Poor cable connections.

2.

Check/clean all connections.

 

3.

Faulty regulator (if so equipped).

3.

Replace regulator.

 

4.

Faulty alternator.

4.

Replace alternator.

 

 

 

 

 

Loss of drive

1.

Freewheel control in “disengaged” position.

1.

Place freewheel control in “engaged” position.

 

2.

Motion drive belt worn, damaged, or broken.

2.

Replace motion drive belt.

 

3.

Air trapped in transmission during shipment

3.

Purge transmission.

 

 

or servicing.

 

 

 

 

 

 

 

Engine “backfires” when

1.

Engine throttle control not set between half and

1.

Move throttle control between half and full speed

turning engine “OFF”

 

full speed (fast) position before stopping engine.

 

(fast) position before stopping engine.

 

 

 

 

 

 

 

 

 

 

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents GT2254 General Operation Safe Operation Practices for Ride-On MowersII. Slope Operation Service General ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Steering Wheel Gauge WheelsSeat Slope SheetAssembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig Assemble Gauge Wheels to Mower Deck SeeInstall Mower and Drive Belt Sees Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Height Adjustment Knob Used to adjust the mower height Know Your TractorHOW to USE Your Tractor To Adjust Gauge Wheels See Fig Using the Reverse Operation SystemTo Operate Mower See Fig Reverse Operation System ROSBefore Starting the Engine Mowing Tips Maintenance Lubrication ChartGeneral Recommendations Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Battery EngineBelts Transaxle CoolingCleaning Service and Adjustments To Install MowerTo Level Mower Housing To Remove Mower See FigFRONT-TO-BACK Adjustment See Figs To Replace Mower Drive Belt See Fig Belt RoutingTo Check and Adjust Brake See Fig To Adjust Attachment Clutch See FigTo Replace Motion Drive Belt See Fig Transmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace FuseOther Fuel SystemEngine OIL CylindersTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic Tractor - Model NO. GT2254 96023000500 Product no 23Electrical 532 14 Battery KEY Part DescriptionChassis and Enclosures 167Repair Parts Ground Drive Repair Parts Steering Assembly 532 19 Wheel, Steering Engine Engine Briggs, Model No H777Order parts from engine Seat Assembly 532 19 SeatDecals Wheels & TiresLift Assembly Repair Parts Mower Deck Repair Parts Gear Drive Transaxle 532 00 Needle Bearing Service Notes Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWarranty Statement Limited Warranty532 19 61-68 Rev 05.16.05 TR
Top Page Image Contents