Husqvarna YTH2648 TF To Move Forward and Backward See Fig, To USE Cruise Control J See Fig

Page 10

OPERATION

TO MOVE FORWARD AND BACKWARD (See Fig. 7)

The direction and speed of movement is controlled by the forward and reverse drive pedals.

•Start tractor and release parking brake.

•Slowly depress forward (K) or reverse (L) drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.

K

J

L

Fig. 7

TO USE CRUISE CONTROL (J) (See Fig. 7)

The cruise control feature can be used for forward travel only.

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

Fig. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

Fig. 9

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut (see "TO ADJUST MOWER CUTTING HEIGHT")

•Start mower blades by engaging attachment clutch control.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents YTH2648 TF General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyTools Required for Assembly ToremovetractorfromcartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Dphg E CJKTo SET Parking Brake See Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged Stopping See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigReverse Operation System ROS See Fig Using the Reverse Operation SystemTo Stop Mower Blades To Operate on HillsCheck Engine OIL Level Service REMINDER/HOUR MeterBefore Starting the Engine ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP General Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningDeck Washout Port See Fig To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig O PSecure with small washer and small retainer spring as shown To Level Mower To Replace Mower Blade Drive Belt To Check BrakeFront Wheel TOE-IN/CAMBER Belt InstallationTo Replace Motion Drive Belt See Fig To Remove Wheel for Repairs See FigReplacing Battery See Fig To Start Engine with a Weak Battery see FIGTo Remove CABLES, Reverse Order Transmission Fuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine continues Wheels and Tires DecalsKEY Part NO. no Description Schematic SCH12Tractor Model NO. YTH2648 TF 96041022500, Product no 41 Electrical KEY Part DescriptionChassis Tractor Model NO. YTH2648 TF 96041022500, Product no 41 Drive 284Transaxle, Tufftorq K46BT Engine Engine Power Rating Information Steering Assembly Seat Assembly 532 42 SeatMower Deck Tractor Model NO. YTH2648 TF 96041022500, Product no 41 Mower Lift    Ggus Whill Only Ride UP and do Hillss Not Acro Axms Reeg DE5112.16.10 AP

YTH2648 TF specifications

The Husqvarna YTH2648 TF is a standout riding lawn mower designed for homeowners seeking efficiency, comfort, and longevity in their lawn care endeavors. With a powerful yet reliable engine, advanced features, and user-friendly design, this mower is ideal for tackling medium to large areas with ease.

One of the most notable features of the YTH2648 TF is its robust 24 HP Briggs & Stratton engine. This engine provides ample power to navigate tough terrains and thick grasses, ensuring efficient cutting performance. The mower's hydrostatic transmission delivers seamless speed adjustments without the need for clutching or shifting, allowing operators to maintain momentum and focus on the task at hand.

The cutting deck of the YTH2648 TF measures 48 inches in width, making it suitable for covering expansive areas quickly. It features a reinforced steel construction that enhances durability and extends the lifespan of the mower, even under rigorous use. The mower’s cutting height can be easily adjusted with a lever, offering six different settings from 1.5 to 4 inches, ensuring precise control over grass length.

Comfort is a key consideration in the design of the YTH2648 TF. It comes equipped with an ergonomic seat that provides support during longer mowing sessions, paired with a soft-grip steering wheel that enhances control. The mower's compact design allows for easy maneuverability around obstacles, such as trees and flower beds, while its tight turning radius ensures that no corners are left uncut.

The Husqvarna YTH2648 TF also features innovative technologies such as the Air Induction mowing technology. This system enhances airflow within the deck, resulting in a cleaner and more consistent cut. Additionally, the mower supports a variety of accessories, like mulching kits and baggers, allowing homeowners to customize their lawn care approach to suit their unique needs.

For added convenience, the YTH2648 TF incorporates easy-to-reach controls and an intuitive dashboard that provides information on fuel levels and speed. A durable front bumper offers protection against accidental impacts, contributing to the mower's overall resilience.

Overall, the Husqvarna YTH2648 TF stands out as a reliable riding mower that combines power, precision, and comfort, making it an excellent choice for homeowners looking to achieve a well-maintained, beautiful lawn with ease.
Top Page Image Contents