Husqvarna Drive Belt Replacement Diagram and Engine Pulley Removal Guide for YTH2648
Page 22

SERVICE AND ADJUSTMENTS

TO REPLACE MOTION DRIVE BELT (See Fig. 37)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Disconnect clutch wire harness (A).

•Remove anti-rotation link (B) on right side of tractor.

•Remove belt from stationary idler (C) and clutching idler (D).

•Remove belt from centerspan idler (E).

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades (F).

•Remove belt downward from engine pulley and around electric clutch (G).

•Slide belt toward rear of tractor, off the steering plate

(H) and remove from tractor.

 

 

G

B

 

H

 

A

 

 

 

 

C

 

 

J

 

 

D

 

 

E

 

 

F

 

 

02953

 

 

electric

Fig. 37

BELT INSTALLATION -

•Install new belt from tractor rear to front, over the steer- ing plate (H) and above clutch brake pedal shaft (J).

•Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley (G).

•Pull belt toward rear of tractor. Carefully work belt down around transmission cooling fan and onto the input pulley (F). Be sure belt is inside the belt keeper.

•Install belt on centerspan idler (E).

•Install belt through stationary idler (C) and clutching idler (D).

•Reinstall anti-rotation link (B) on right side of tractor. Tighten securely.

•Reconnect clutch harness (A).

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this section of manual).

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 38)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

Fig. 38

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents YTH2648 TF General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyTools Required for Assembly ToremovetractorfromcartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor Dphg E CJKTo SET Parking Brake See Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged Stopping See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigReverse Operation System ROS See Fig Using the Reverse Operation SystemTo Stop Mower Blades To Operate on HillsCheck Engine OIL Level Service REMINDER/HOUR MeterBefore Starting the Engine ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP General Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningDeck Washout Port See Fig To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig O PSecure with small washer and small retainer spring as shown To Level Mower To Replace Mower Blade Drive Belt To Check BrakeFront Wheel TOE-IN/CAMBER Belt InstallationTo Replace Motion Drive Belt See Fig To Remove Wheel for Repairs See FigReplacing Battery See Fig To Start Engine with a Weak Battery see FIGTo Remove CABLES, Reverse Order Transmission Fuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine continues Wheels and Tires DecalsKEY Part NO. no Description Schematic SCH12Tractor Model NO. YTH2648 TF 96041022500, Product no 41 Electrical KEY Part DescriptionChassis Tractor Model NO. YTH2648 TF 96041022500, Product no 41 Drive 284Transaxle, Tufftorq K46BT Engine Engine Power Rating Information Steering Assembly Seat Assembly 532 42 SeatMower Deck Tractor Model NO. YTH2648 TF 96041022500, Product no 41 Mower Lift    Ggus Whill Only Ride UP and do Hillss Not Acro Axms Reeg DE5112.16.10 AP

YTH2648 TF specifications

The Husqvarna YTH2648 TF is a standout riding lawn mower designed for homeowners seeking efficiency, comfort, and longevity in their lawn care endeavors. With a powerful yet reliable engine, advanced features, and user-friendly design, this mower is ideal for tackling medium to large areas with ease.

One of the most notable features of the YTH2648 TF is its robust 24 HP Briggs & Stratton engine. This engine provides ample power to navigate tough terrains and thick grasses, ensuring efficient cutting performance. The mower's hydrostatic transmission delivers seamless speed adjustments without the need for clutching or shifting, allowing operators to maintain momentum and focus on the task at hand.

The cutting deck of the YTH2648 TF measures 48 inches in width, making it suitable for covering expansive areas quickly. It features a reinforced steel construction that enhances durability and extends the lifespan of the mower, even under rigorous use. The mower’s cutting height can be easily adjusted with a lever, offering six different settings from 1.5 to 4 inches, ensuring precise control over grass length.

Comfort is a key consideration in the design of the YTH2648 TF. It comes equipped with an ergonomic seat that provides support during longer mowing sessions, paired with a soft-grip steering wheel that enhances control. The mower's compact design allows for easy maneuverability around obstacles, such as trees and flower beds, while its tight turning radius ensures that no corners are left uncut.

The Husqvarna YTH2648 TF also features innovative technologies such as the Air Induction mowing technology. This system enhances airflow within the deck, resulting in a cleaner and more consistent cut. Additionally, the mower supports a variety of accessories, like mulching kits and baggers, allowing homeowners to customize their lawn care approach to suit their unique needs.

For added convenience, the YTH2648 TF incorporates easy-to-reach controls and an intuitive dashboard that provides information on fuel levels and speed. A durable front bumper offers protection against accidental impacts, contributing to the mower's overall resilience.

Overall, the Husqvarna YTH2648 TF stands out as a reliable riding mower that combines power, precision, and comfort, making it an excellent choice for homeowners looking to achieve a well-maintained, beautiful lawn with ease.
Top Page Image Contents