Husqvarna YTH2648 TF owner manual To Level Mower

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER

Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly.

VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 30)

With all tires properly inflated and if your lawn appears unevenly cut, determine which side of mower is cutting lower.

NOTE: As desired, you can raise the low side of mower or lower the high side.

Go to side of mower you wish to adjust.

With a 3/4" or adjustable wrench, turn lift link adjust- ment nut (A) to the left to lower the mower, or, to the right to raise the mower.

If adjustment is necessary, see steps in Visual Adjust- ment instructions above.

Recheck measurements, adjust if necessary until both sides are equal.

FRONT-TO-BACK ADJUSTMENT (See Figs. 32 & 33) IMPORTANT: Deck must be level side-to-side.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

Raise mower to highest position.

Position any blade so the tip is pointing straight forward.

TURN NUT RIGHT TO RAISE MOWER

A

TURN NUT LEFT

TO LOWER MOWER

Measure distance (B) to the ground at front and rear

tip of the blade.

BB

Fig. 32

If front tip of blade is not 1/8" to 1/2" lower than the

 

rear tip, go to the front of tractor.

With an 11/16" or adjustable wrench, loosen jam nut

 

A several turns to clear adjustment nut B.

Fig. 30

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

Test your adjustment by mowing some uncut grass and visually checking the appearance. Readjust, if necessary, until you are satisfied with the results.

PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 31)

With all tires properly inflated, park tractor on level ground or driveway.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

Raise mower to its highest position.

At both sides of mower, position blade at side and measure the distance (A) from bottom edge of blade to the ground. The distance should be the same on both sides.

 

02966

A

A

Fig. 31

• With a 3/4" or adjustable wrench, turn front link adjust-

ment nut (B) clockwise (tighten) to raise the front of mow-

er,or,counterclockwise(loosen)tolowerthefrontmower.

 

A

 

B

TIGHTEN

LOOSEN

ADJUST

ADJUST

NUT B

NUT B TO

TO RAISE

LOWER

MOWER

MOWER

 

LOOSEN JAM

 

NUT A FIRST

Fig. 33

NOTE: Each full turn of the adjustment nut will change mower height about 1/8".

Recheck measurements, adjust if necessary until front tip of blade is 1/8" to 1/2" lower than the rear tip.

Hold adjustment nut in position with wrench and tighten jam nut securely against adjustment nut.

20

Image 20
Contents YTH2648 TF Safety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Assembly Tools Required for AssemblyUnassembled Parts ToremovetractorfromcartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor Dphg E CJKHOW to USE Your Tractor Attachment Clutch Switch Disengaged EngagedTo SET Parking Brake See Fig Stopping See FigTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigTo Move Forward and Backward See Fig To USE Cruise Control J See FigUsing the Reverse Operation System To Stop Mower BladesReverse Operation System ROS See Fig To Operate on HillsService REMINDER/HOUR Meter Before Starting the EngineCheck Engine OIL Level ADD GasolineAutomatic Transmission Warm UP Mowing TipsPurge Transmission Maintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBlade Care Blade Removal See FigEngine Deck Washout Port See Fig CleaningIN-LINE Fuel Filter See Fig Service and Adjustments To Install Mower See FigTo Remove Mower See Fig O PSecure with small washer and small retainer spring as shown To Level Mower To Replace Mower Blade Drive Belt To Check BrakeBelt Installation To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Remove CABLES, Reverse Order To Start Engine with a Weak Battery see FIGReplacing Battery See Fig Transmission Storage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine continues KEY Part NO. no Description DecalsWheels and Tires Schematic SCH12Tractor Model NO. YTH2648 TF 96041022500, Product no 41 Electrical KEY Part DescriptionChassis Tractor Model NO. YTH2648 TF 96041022500, Product no 41 Drive 284Transaxle, Tufftorq K46BT Engine Engine Power Rating Information Steering Assembly Seat Assembly 532 42 SeatMower Deck Tractor Model NO. YTH2648 TF 96041022500, Product no 41 Mower Lift    Ggus Whill Only Ride UP and do Hillss Not Acro Axms Reeg DE5112.16.10 AP

YTH2648 TF specifications

The Husqvarna YTH2648 TF is a standout riding lawn mower designed for homeowners seeking efficiency, comfort, and longevity in their lawn care endeavors. With a powerful yet reliable engine, advanced features, and user-friendly design, this mower is ideal for tackling medium to large areas with ease.

One of the most notable features of the YTH2648 TF is its robust 24 HP Briggs & Stratton engine. This engine provides ample power to navigate tough terrains and thick grasses, ensuring efficient cutting performance. The mower's hydrostatic transmission delivers seamless speed adjustments without the need for clutching or shifting, allowing operators to maintain momentum and focus on the task at hand.

The cutting deck of the YTH2648 TF measures 48 inches in width, making it suitable for covering expansive areas quickly. It features a reinforced steel construction that enhances durability and extends the lifespan of the mower, even under rigorous use. The mower’s cutting height can be easily adjusted with a lever, offering six different settings from 1.5 to 4 inches, ensuring precise control over grass length.

Comfort is a key consideration in the design of the YTH2648 TF. It comes equipped with an ergonomic seat that provides support during longer mowing sessions, paired with a soft-grip steering wheel that enhances control. The mower's compact design allows for easy maneuverability around obstacles, such as trees and flower beds, while its tight turning radius ensures that no corners are left uncut.

The Husqvarna YTH2648 TF also features innovative technologies such as the Air Induction mowing technology. This system enhances airflow within the deck, resulting in a cleaner and more consistent cut. Additionally, the mower supports a variety of accessories, like mulching kits and baggers, allowing homeowners to customize their lawn care approach to suit their unique needs.

For added convenience, the YTH2648 TF incorporates easy-to-reach controls and an intuitive dashboard that provides information on fuel levels and speed. A durable front bumper offers protection against accidental impacts, contributing to the mower's overall resilience.

Overall, the Husqvarna YTH2648 TF stands out as a reliable riding mower that combines power, precision, and comfort, making it an excellent choice for homeowners looking to achieve a well-maintained, beautiful lawn with ease.