Husqvarna YTH2754T manual Assembly, Mower Drive Belt Installation

Page 8
MOWER DRIVE BELT INSTALLATION

ASSEMBLY

•FIRST INSTALL ANTI-SWAY BAR (S).

•From right side of mower, insert anti-sway bar into hole in transmission bracket (T).

 

T

S

 

 

A

 

•

 

 

Fig. 7

• Pivot bar towards you and insert other end of bar

•

 

into hole in rear mower bracket (D). Move mower

•

as needed to insert bar.

•Secure with washer and retainer spring as shown

D Manual background

•

C

D

Fig. 10

ATTACH FRONT LINK (E) - Work from left side of tractor. Insert rod end of link assembly through front hole in trac- tor front suspension bracket (F) and secure with retainer spring (G) through hole in link located behind the bracket.

Insert other end of link (E) into hole in front mower bracket

(H)and secure with washer and retainer spring (J). Disengage belt tension rod (K) from locking bracket (L).

EH J

FManual background

G

Fig. 11

Install belt onto engine clutch pulley (M).

Fig. 8

•ATTACH MOWER SIDE SUSPENSION ARMS (A) TO CHASSIS - Position hole in arm over pin (B) on outside of tractor chassis and secure with retainer spring.

•Repeat on opposite side of tractor.

A

B

Fig. 9

•ATTACH REAR LIFT LINKS (C) - Lift rear corner of mower and position slot in link assembly over pin on rear mower bracket (D) and secure with washer and retainer spring.

•Repeat on opposite side of tractor.

•Turn steering wheel to position wheels straight forward.

M

Fig. 12

IMPORTANT: Check belt for proper routing in all mower pulley grooves.

•Engage belt tension rod (K) on locking bracket (L).

CAUTION: Belt tension rod is spring loaded. Have a tight grip on rod and engage slowly.

•Raise attachment lift lever to highest position.

•If necessary, adjust gauge wheels before operating mower as shown in the Operation section of this manual.

MOWER DRIVE BELT INSTALLATION

Follow procedure described in “TO REPLACE MOWER BLADE DRIVE BELT ” in the "Service and Adjustments" section of this manual.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Operators Manual YTH2754TSAFETY RULES Safe Operation Practices for Ride-OnMowersI. GENERAL OPERATION II. SLOPE OPERATIONV. SERVICE III. CHILDRENIV. TOWING GENERAL SERVICETABLE OF CONTENTS PRODUCT SPECIFICATIONSCUSTOMER RESPONSIBILITIES 10-16UNASSEMBLED PARTS MowerMower Front Wheel Slope SheetASSEMBLY TOOLS REQUIRED FOR ASSEMBLYADJUST SEAT See Fig TO CHECK BATTERY See FigTO INSTALL MOWER See Figs ASSEMBLE FRONT WHEEL TO MOWER See FigDC D FIg. LB MMOWER DRIVE BELT INSTALLATION ASSEMBLE GAUGE WHEELS TO MOWER DECK See Fig CHECK TIRE PRESSURECHECK DECK LEVELNESS CHECK FOR PROPER POSITION OF ALL BELTSOPERATION KNOW YOUR TRACTOR HOW TO USE YOUR TRACTOR TO SET PARKING BRAKE See FigSTOPPING See Fig TO USE THROTTLE CONTROL D See FigTO ADJUST MOWER CUTTING HEIGHT See Fig TO ADJUST GAUGE WHEELS See FigTO MOVE FORWARD AND BACKWARD See Fig TO USE CRUISE CONTROL J See FigTO STOP MOWER BLADES REVERSE OPERATION SYSTEM ROSTO OPERATE ON HILLS TO TRANSPORT See Figs. 14 andSERVICE REMINDER/HOUR METER BEFORE STARTING THE ENGINECHECK ENGINE OIL LEVEL ADD GASOLINEMOWING TIPS PURGE TRANSMISSIONMAINTENANCE LUBRICATION CHARTBATTERY TRACTORBRAKE OPERATION TIRESCLEAN AIR SCREEN ENGINEV-BELTS TRANSAXLE COOLINGCLEANING ENGINE OIL FILTERMUFFLER SPARK PLUGSSERVICE AND ADJUSTMENTS TO INSTALL MOWERTRACTOR See Fig. TO REMOVE MOWER TO LEVEL MOWERSERVICE AND ADJUSTMENTS TO REPLACE MOTION DRIVE BELT See Fig TO REPLACE MOWER BLADE DRIVE BELTTO CHECK BRAKE TO REMOVE WHEEL FOR REPAIRS See Fig TO START ENGINE WITH A WEAK BATTERY See FigFRONT WHEEL TOE-IN/CAMBER REPLACING BATTERY See Fig TO REMOVE HOOD AND GRILL ASSEMBLY See FigTO ADJUST THROTTLE CONTROL CABLE TO ADJUST CHOKE CONTROLSTORAGE OTHERFUEL SYSTEM ENGINE OILTROUBLESHOOTING POINTS PROBLEMLoss of power CAUSErun when operator Battery will not chargewhen turning Engine dies whenONLY RIDE UP AND DOWN HILL NOT ACROSS HILL 15 DEGREES MAXSERVICE NOTES SERVICE NOTES Charlotte, NC WARRANTY STATEMENT2008
Top Page Image Contents