Harman AVR 2600 owner manual Operation, Turning on the AVR, Volume Control, Dolby Volume

Page 29

OPERATION

Now that you have installed your components and completed a basic configuration, you are ready to begin enjoying your home theater system.

TURNING ON THE AVR 2600

Flip the rear-panel Main Power Switch to the “On” position. The Power Indicator on the front panel will turn amber, indicating that the AVR is in Standby mode and is ready to be turned on. The Main Power Switch is normally left on.

There are several ways to turn on the AVR 2600:

a)Press the Standby/On Switch on the front panel.

b)Using the remote, press the AVR Power On Button or any of the Source Selectors.

To turn the receiver off, press either the Standby/On Switch on the front panel or the AVR Power Off Button on the remote control. Unless the receiver will not be used for an extended period of time, leave the Main Power Switch on. When the Main Power Switch is turned off, any settings you have programmed will be preserved for up to four weeks.

IMPORTANT NOTE: If the PROTECT message ever appears in the Message Display, turn off the AVR and unplug it. Check all speaker wires for a short. If none is found, bring the unit to an authorized Harman Kardon service center for inspection and repair before using it again.

VOLUME CONTROL

Adjust the volume either by turning the knob on the front panel (clockwise to increase volume or counterclockwise to decrease volume), or by pressing the Volume Control on the remote. The volume is displayed as a negative number of decibels (dB) below the 0dB reference point.

0dB is the maximum recommended volume for the AVR 2600. Although it’s possible to turn the volume to a higher level, doing so may damage your hearing and your speakers. For certain more dynamic audio materials, even 0dB may be too high, allowing for damage to equipment. Use caution with regard to volume levels.

To change the volume level display from the default decibel scale to a 0-to-90 scale, adjust the Volume Units setting in the System Settings menu, as described on page 42.

Dolby Volume

The AVR 2600 implements Dolby Volume processing, which can improve the audio performance of the system by revealing subtle details even at normal home-listening volumes.

One concern of the typical home theater listener is that volumes can vary widely for different programs played by a source, e.g., television commercial advertisements are often much louder than the main feature. Another is that details heard in the recording studio at typically high reference volumes are lost at the lower volumes used by many listeners.

The AVR 2600 uses two Dolby Volume techniques to address these issues. The Leveler module maintains a consistent listening volume within a source, e.g., while watching commercial television or while listening to different tracks on a data CD. The Modeler module

endeavors to re-create the reference presentation that was heard in the recording studio without losing portions of the program at the typically lower volume levels often used in the home. When the Modeler module is active, you may notice details of the performance that were hidden when the program was played on other equipment.

NOTE: The Dolby Volume processor is not used to level volume across sources.

To adjust the Dolby Volume setting, press the Audio Effects Button. A screen similar to the one shown in Figure 27 will appear. Move the cursor to highlight the Dolby Volume setting, and each press of the OK Button will switch to one of the options in Table 4 below. The settings do not refer to the volume level, which is adjusted normally using the Volume Control, but rather to the amount of Dolby Volume processing desired.

Figure 27 – Adjust Dolby Volume

Table 4 – Dolby Volume Settings

Setting

Effect

Off

No Dolby Volume processing

Low

Only Dolby Volume Modeler module is active

Medium

Both Modeler and Leveler modules are active;

 

Leveler module has a value of 3

Max

Both Modeler and Leveler modules are active;

 

Leveler module has a value of 9

NOTE: Dolby Volume processing is compatible with sources recorded at a sampling rate of 48kHz. High-resolution sources, such as DTS 96/24, will be decoded at 48kHz. DTS 96/24 programs will be played in DTS 5.1 mode. To hear DTS 96/24 materials in high resolution, turn off Dolby Volume processing.

Dolby Volume Calibration Offset

Calibration Offset is a feature of Dolby Volume processing that allows you to adjust the calibration of the AVR 2600 to optimally match your speakers and listening environment. The AVR 2600 is calibrated with the average speaker sensitivity in mind; however, different speakers may have different sensitivities. Use Calibration Offset to adjust the calibration of the AVR 2600 according to the types of speakers you have.

The average home audio speaker sensitivity is 88dB SPL (8 ohms, 1 watt, 1 meter). Check the sensitivity specification for your loud- speakers, found in the owner’s manual or on the manufacturer’s Web site. If your speakers have a sensitivity rating greater than 88dB SPL, increase Calibration Offset by the difference between

29

Image 29
Contents AVR Important Safety Instructions Safety InformationService Instructions Outdoor Use Marking Wet Location MarkingUnpacking Important Safety InformationTable of Contents Surround Modes IntroductionAudio Inputs Supplied AccessoriesAudio/Video Inputs Digital Audio InputsControls FrontPanel FRONT-PANEL Controls On When the AVR is turned on, this LED turns whiteVolume Knob Turn this knob to raise or lower the volume Rear ConnectionsAlways make a separate audio connection REAR-PANEL ConnectionsUse an HDMI-to-DVI adapter AM and FM Antenna Terminals Connect the included Main Remote Control Functions Surround Modes Press to directly access the Surround AVR Power Off Button Press to turn off the AVRMain Remote Control Functions Multichannel Audio Introduction to Home TheaterTypical Home Theater System Speaker Connections Connecting Source Devices to the AVRSubwoofer Audio ConnectionsAnalog Audio Video ConnectionsDigital Video Analog VideoUSB Port AntennasFront Speaker Placement Speaker PlacementPlacement of Surround Speakers in a 5.1-Channel System Subwoofer PlacementGame Media Server Getting StartedSource Assignment Worksheet Getting Started Installation Step TEN Plug in AC Power Cords Step Nine Install a Multizone SystemPlug the AC Power cord into an unswitched AC outlet Step SIX Connect AM AntennaTwo steps are required the first time you turn on the AVR Step Twelve Program Sources Into the RemoteStep Thirteen Turn On the AVR Configure the AVR 2600, Using EzSet/EQ Technology Initial SetupUsing the ON-SCREEN Menu System Audio and Video Input Selection Set Up SourcesChannel Inputs You are now ready to begin enjoying your new receiver Dolby Volume Volume ControlDolby Volume Calibration Offset OperationHeadphones Sleep TimerUsing the Radio Mute FunctionRecording Sirius Satellite Radio OperationUsing The Bridge Using Docking StationRemote Control Key Previous TrackSelecting a Surround Mode IPod Manual ModePlay Pause Menu Back/Exit or Left Arrow Select Right ArrowOperation Digital Audio Signals Analog Audio SignalsAdvanced Functions Audio Processing and Surround SoundVideo Game Logic 7 Game Dolby Surround SettingsManual Speaker Setup Step ONE Determine Speaker Crossover Step Three Manual Setup MenuStep TWO Measure Speaker Distances Number of SpeakersSub Mode Adjust Crossover Frequencies MenuAdjust Speaker Distance Menu Video Adjustments Step Four Setting Channel Output Levels ManuallyVideo Modes Menu Video ModesBrightness Adjustment General AVR Settings System SettingsMenu Appearance Advanced Remote Control FunctionsSystem Information Punch-Through ProgrammingProcessor Reset Resetting the RemoteMemory To program, or record an activity, follow these stepsSymptom Cause Solution Troubleshooting GuideTable A1 Recommended Source Component Connections Table A2 Source Setting DefaultsAppendix Table A4 Delay Setting Defaults Table A3 Speaker/Channel Setting DefaultsAll Digital and 2-Channel Your Settings Analog Audio Inputs PositionTable A6 Audio Effects Settings Table A5 Source SettingsDefault Media Server Radio GameBlack Level Off Deinterlacing Film Mode Detect Table A7 Video Modes SettingsTable A8 Surround Modes Auto SelectTable A11 Zone 2 Settings Table A9 Remote Control CodesTable A10 System Settings Table A12 Surround Modes Surround Mode Description Incoming Bitstream or SignalTable A12 Channel music recordings DTS 2/2/.0 or .1, 3/2/.0 orChannel Stereo Center speaker plays a summed mono mix36 37 38 40 41 Radio Table A13 Remote Control Function ListAUX Table A13Table A14 Remote Control Product Codes TV Table A16 VCR Table A15 Remote Control Product Codes AUX-HDTVTable A16 Remote Control Product Codes AUX-VCR Table A17 CD Table A17 Remote Control Product Codes AUX-CDTable A18 Remote Control Product Codes DVD Table A21 Remote Control Product Codes Cable Table A19 Remote Control Product Codes SATTable A20 Remote Control Product Codes Game Table A21 Cable Table A24 Remote Control Product Codes AUX- TiVoTable A22 Remote Control Product Codes Media Server Audio Section AVR 2600 Technical Specifications

AVR 2600 specifications

The Harman AVR 2600 is a feature-rich audio-video receiver designed to elevate your home entertainment experience. As part of Harman's renowned line of audio products, the AVR 2600 seamlessly combines advanced technology with user-friendly design, making it a popular choice for audiophiles and casual listeners alike.

One of the standout features of the AVR 2600 is its robust power output. With a rated 7.1 channel amplifier, it delivers a powerful and immersive sound experience. Each channel produces a significant amount of wattage, ensuring that your movies, music, and games sound spectacular and enveloping. This power enables the AVR 2600 to drive a variety of speaker configurations, allowing users to customize their sound setup according to their preferences.

In terms of connectivity, the Harman AVR 2600 boasts multiple HDMI inputs and outputs, supporting the latest video formats, including 4K. This allows users to connect multiple devices, such as gaming consoles, Blu-ray players, and streaming devices, all while maintaining a simple and clutter-free setup. The receiver also features built-in Bluetooth technology, enabling wireless streaming of music from smartphones, tablets, and other compatible devices. This versatility enhances the overall user experience, making it easy to access your favorite content.

The AVR 2600 also incorporates advanced audio processing technologies. With support for popular surround sound formats like Dolby Atmos and DTS:X, users can experience cinematic sound quality right in their living rooms. These technologies provide a three-dimensional audio experience, enhancing the immersion when watching movies or playing video games.

Another significant characteristic of the AVR 2600 is its user-friendly interface. Navigating the receiver is straightforward, thanks to the on-screen setup and intuitive remote control. The built-in setup assistant guides users through the calibration process, allowing for optimal speaker placement and sound adjustment based on the room's acoustics.

In conclusion, the Harman AVR 2600 is a powerful and versatile audio-video receiver that combines high-quality sound, advanced connectivity options, and user-friendly features. Whether you're looking to create the ultimate home theater experience or simply elevate your music listening, the AVR 2600 is an excellent choice that meets a wide range of entertainment needs.