Harman AVR 2600 owner manual Important Safety Information, Unpacking

Page 3

SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION

Verify Line Voltage Before Use

Your AVR 2600 has been designed for use with 120-volt AC current. Connection to a line voltage other than that for which it is intended can create a safety and fire hazard and may damage the unit.

If you have any questions about the voltage requirements for your specific model, or about the line voltage in your area, contact your selling dealer before plugging the unit into a wall outlet.

Do Not Use Extension Cords

To avoid safety hazards, use only the power cord attached to your unit. We do not recommend that extension cords be used with this product. As with all electrical devices, do not run power cords under rugs or carpets or place heavy objects on them. Damaged power cords should be replaced immediately by an authorized service center with a cord meeting factory specifications.

Handle the AC Power Cord Gently

When disconnecting the power cord from an AC outlet, always pull the plug; never pull the cord. If you do not intend to use the unit for any considerable length of time, disconnect the plug from the AC outlet.

Do Not Open the Cabinet

There are no user-serviceable components inside this product. Opening the cabinet may present a shock hazard, and any modification to the product will void your warranty. If water or any metal object such as a paper clip, wire or staple accidentally falls inside the unit, disconnect it from the AC power source immediately, and consult an authorized service center.

CATV or Antenna Grounding

If an outside antenna or cable system is connected to this product, be certain that it is grounded so as to provide some protection against voltage surges and static charges. Section 810 of the National Electrical Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and require- ments of the grounding electrode.

NOTE TO CATV SYSTEM INSTALLER: This reminder is provided

to call the CATV (cable TV) system installer’s attention to article 820-40 of the NEC, which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as possible.

Installation Location

To ensure proper operation and to avoid the potential for safety hazards, place the unit on a firm and level surface. When placing the unit on a shelf, be certain that the shelf and any mounting hardware can support the weight of the product.

Make certain that proper space is provided both above and below the unit for ventilation. If this product will be installed in a cabinet or other enclosed area, make certain that there is sufficient air movement within the cabinet. Under some circumstances, a fan may be required.

Do not place the unit directly on a carpeted surface.

Avoid installation in extremely hot or cold locations, or in an area that is exposed to direct sunlight or heating equipment.

Avoid moist or humid locations.

Do not obstruct the ventilation slots on the top of the unit, or place objects directly over them.

Due to the weight of the AVR 2600 and the heat generated by the ampli- fiers, there is the remote possibility that the rubber padding on the bottom of the unit’s feet may leave marks on certain wood or veneer materials.

Use caution when placing the unit on soft woods or other materials that may be damaged by heat or heavy objects. Some surface finishes may be particularly sensitive to absorbing such marks, due to a variety of factors

beyond our control, including the nature of the finish, cleaning materials used, and normal heat and vibration caused by the use of the product, or other factors. We recommend that caution be exercised in choosing an installation location for the component and in normal maintenance practices, as your warranty will not cover this type of damage to furniture.

Cleaning

When the unit gets dirty, wipe it with a clean, soft, dry cloth. If necessary, and only after unplugging the AC power cord, wipe it with a soft cloth dampened with mild soapy water, then a fresh cloth with clean water. Wipe it dry immediately with a dry cloth. NEVER use benzene, aerosol cleaners, thinner, alcohol or any other volatile cleaning agent. Do not use abrasive cleaners, as they may damage the finish of metal parts. Avoid spraying insecticide near the unit.

Moving the Unit

Before moving the unit, be certain to disconnect any interconnection cords with other components, and make certain that you disconnect the unit from the AC outlet.

Important Information for the User

This equipment has been tested and found to comply with the limits for a Class-B digital device, pursuant to Part 15 of the FCC Rules. The limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio-frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that harmful interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interfer- ence by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful inter- ference, and (2) this device must accept interference received, including interference that may cause undesired operation.

NOTE: Changes or modifications may cause this unit to fail to comply with Part 15 of the FCC Rules and may void the user’s authority to operate the equipment.

UNPACKING

The carton and shipping materials used to protect your new receiver during shipment were specially designed to cushion it from shock and vibration. We suggest that you save the carton and packing materials for use in ship- ping if you move, or should the unit ever need repair.

To minimize the size of the carton in storage, you may wish to flatten it. This is done by carefully slitting the tape seams on the bottom and collaps- ing the carton. Other cardboard inserts may be stored in the same manner. Packing materials that cannot be collapsed should be saved along with the carton in a plastic bag.

If you do not wish to save the packaging materials, please note that the carton and other sections of the shipping protection are recyclable. Please respect the environment and discard those materials at a local recycling center.

It is important that you remove the protective plastic film from the front- panel lens. Leaving the film in place will affect the performance of your remote control.

3

Image 3
Contents AVR Wet Location Marking Safety InformationImportant Safety Instructions Service Instructions Outdoor Use MarkingUnpacking Important Safety InformationTable of Contents Surround Modes IntroductionDigital Audio Inputs Supplied AccessoriesAudio Inputs Audio/Video InputsFront PanelControls On When the AVR is turned on, this LED turns white Volume Knob Turn this knob to raise or lower the volumeFRONT-PANEL Controls Rear ConnectionsREAR-PANEL Connections Use an HDMI-to-DVI adapterAlways make a separate audio connection AM and FM Antenna Terminals Connect the included Main Remote Control Functions Surround Modes Press to directly access the Surround AVR Power Off Button Press to turn off the AVRMain Remote Control Functions Introduction to Home Theater Typical Home Theater SystemMultichannel Audio Audio Connections Connecting Source Devices to the AVRSpeaker Connections SubwooferAnalog Video Video ConnectionsAnalog Audio Digital VideoUSB Port AntennasSubwoofer Placement Speaker PlacementFront Speaker Placement Placement of Surround Speakers in a 5.1-Channel SystemGetting Started Source Assignment WorksheetGame Media Server Getting Started Installation Step SIX Connect AM Antenna Step Nine Install a Multizone SystemStep TEN Plug in AC Power Cords Plug the AC Power cord into an unswitched AC outletStep Twelve Program Sources Into the Remote Step Thirteen Turn On the AVRTwo steps are required the first time you turn on the AVR Initial Setup Using the ON-SCREEN Menu SystemConfigure the AVR 2600, Using EzSet/EQ Technology Audio and Video Input Selection Set Up SourcesChannel Inputs You are now ready to begin enjoying your new receiver Operation Volume ControlDolby Volume Dolby Volume Calibration OffsetMute Function Sleep TimerHeadphones Using the RadioRecording Sirius Satellite Radio OperationPrevious Track Using Docking StationUsing The Bridge Remote Control KeyRight Arrow IPod Manual ModeSelecting a Surround Mode Play Pause Menu Back/Exit or Left Arrow SelectOperation Audio Processing and Surround Sound Analog Audio SignalsDigital Audio Signals Advanced FunctionsDolby Surround Settings Manual Speaker SetupVideo Game Logic 7 Game Number of Speakers Step Three Manual Setup MenuStep ONE Determine Speaker Crossover Step TWO Measure Speaker DistancesAdjust Crossover Frequencies Menu Adjust Speaker Distance MenuSub Mode Video Adjustments Step Four Setting Channel Output Levels ManuallyVideo Modes Menu Video ModesBrightness Adjustment General AVR Settings System SettingsPunch-Through Programming Advanced Remote Control FunctionsMenu Appearance System InformationTo program, or record an activity, follow these steps Resetting the RemoteProcessor Reset MemorySymptom Cause Solution Troubleshooting GuideTable A2 Source Setting Defaults AppendixTable A1 Recommended Source Component Connections Position Table A3 Speaker/Channel Setting DefaultsTable A4 Delay Setting Defaults All Digital and 2-Channel Your Settings Analog Audio InputsMedia Server Radio Game Table A5 Source SettingsTable A6 Audio Effects Settings DefaultAuto Select Table A7 Video Modes SettingsBlack Level Off Deinterlacing Film Mode Detect Table A8 Surround ModesTable A9 Remote Control Codes Table A10 System SettingsTable A11 Zone 2 Settings Table A12 Surround Modes Surround Mode Description Incoming Bitstream or SignalTable A12 Center speaker plays a summed mono mix DTS 2/2/.0 or .1, 3/2/.0 orChannel music recordings Channel Stereo36 37 38 40 41 Radio Table A13 Remote Control Function ListAUX Table A13Table A14 Remote Control Product Codes TV Table A15 Remote Control Product Codes AUX-HDTV Table A16 Remote Control Product Codes AUX-VCRTable A16 VCR Table A17 Remote Control Product Codes AUX-CD Table A18 Remote Control Product Codes DVDTable A17 CD Table A19 Remote Control Product Codes SAT Table A20 Remote Control Product Codes GameTable A21 Remote Control Product Codes Cable Table A24 Remote Control Product Codes AUX- TiVo Table A22 Remote Control Product Codes Media ServerTable A21 Cable Audio Section AVR 2600 Technical Specifications

AVR 2600 specifications

The Harman AVR 2600 is a feature-rich audio-video receiver designed to elevate your home entertainment experience. As part of Harman's renowned line of audio products, the AVR 2600 seamlessly combines advanced technology with user-friendly design, making it a popular choice for audiophiles and casual listeners alike.

One of the standout features of the AVR 2600 is its robust power output. With a rated 7.1 channel amplifier, it delivers a powerful and immersive sound experience. Each channel produces a significant amount of wattage, ensuring that your movies, music, and games sound spectacular and enveloping. This power enables the AVR 2600 to drive a variety of speaker configurations, allowing users to customize their sound setup according to their preferences.

In terms of connectivity, the Harman AVR 2600 boasts multiple HDMI inputs and outputs, supporting the latest video formats, including 4K. This allows users to connect multiple devices, such as gaming consoles, Blu-ray players, and streaming devices, all while maintaining a simple and clutter-free setup. The receiver also features built-in Bluetooth technology, enabling wireless streaming of music from smartphones, tablets, and other compatible devices. This versatility enhances the overall user experience, making it easy to access your favorite content.

The AVR 2600 also incorporates advanced audio processing technologies. With support for popular surround sound formats like Dolby Atmos and DTS:X, users can experience cinematic sound quality right in their living rooms. These technologies provide a three-dimensional audio experience, enhancing the immersion when watching movies or playing video games.

Another significant characteristic of the AVR 2600 is its user-friendly interface. Navigating the receiver is straightforward, thanks to the on-screen setup and intuitive remote control. The built-in setup assistant guides users through the calibration process, allowing for optimal speaker placement and sound adjustment based on the room's acoustics.

In conclusion, the Harman AVR 2600 is a powerful and versatile audio-video receiver that combines high-quality sound, advanced connectivity options, and user-friendly features. Whether you're looking to create the ultimate home theater experience or simply elevate your music listening, the AVR 2600 is an excellent choice that meets a wide range of entertainment needs.