Harman AVR 2600 Mute Function, Sleep Timer, Audio Effects, Source Selection, Video Modes

Page 30

OPERATION

your speakers’ sensitivity and 88dB. If they have a sensitivity rating of less than 88dB SPL, decrease Calibration Offset by the difference between your speakers’ sensitivity and 88dB.

To adjust the Calibration Offset, press the Setup Button and scroll to the System Setup menu, then select it. Scroll to the Dolby Volume Calibration line, which defaults to 0dB. Use the 7/3 Buttons to adjust the setting within the range of – 10dB to +10dB.

MUTE FUNCTION

To temporarily mute all speakers and the headphones, press the Mute Button on the remote. Any recording in progress will not be affected. The MUTE message will appear in the display as a reminder. To restore normal audio, press the Mute Button again, or adjust the volume. Turning off the AVR will also end muting.

SLEEP TIMER

The sleep timer sets the AVR to play for up to 90 minutes and then turn off automatically.

Press the Sleep Settings Button on the remote, and the time until turn-off will be displayed. Each additional press of the Sleep Button increases the play time by 10 minutes, with a maximum of 90 minutes. The SLEEP OFF setting disables the sleep timer.

When the sleep timer has been set, the front-panel display will automatically dim to half-brightness.

If you press the Sleep Button after the timer has been set, the remaining play time will be displayed. Press the Sleep Button again to change the play time.

AUDIO EFFECTS

Adjust the Dolby Volume setting, tone controls, LFE trim, Equalization On/Off setting or MP3 enhancement to improve performance. Access these settings from the Audio Effects submenu, as described in the Advanced Functions section.

It is recommended that you leave the settings at their default values until you are more familiar with your system.

SOURCE SELECTION

Press the front-panel Source List Button. Use the 5/1 Buttons to scroll through the sources. Using the on-screen menus, press the Setup Button, highlight “Source Select” and press the OK Button. Scroll to the desired source in the slide-show menu and press the OK Button.

For direct access to any source, press its Source Selector on the remote.

The AVR selects the audio and video inputs assigned to the source, and any other settings made during setup.

The source name, the audio and video inputs assigned to the source, and the surround mode will appear on the front panel. The source name and surround mode will also appear on screen.

VIDEO TROUBLESHOOTING TIPS:

If there is no picture:

•Check the source selection and video input assignment.

•Check the wires for a loose or incorrect connection.

•Check the video input selection on the display device (TV).

•Press the front-panel Resolution Button and use the

5/1 Buttons until the correct video output resolution is selected and a picture appears. The CANCEL message will appear. Press the 5Button to view the ACCEPT option, then press the OK Button.

Additional Tips for HDMI Connections:

•Turn off all devices (including the TV, AVR and any source components).

•Unplug the HDMI cables, starting with the cable between the TV and AVR, and continuing with the cables between the AVR and each source device.

•Carefully reconnect the cables from the source devices to the AVR. Connect the cable from the AVR to the TV last.

•Turn on the devices in this order: TV, AVR, source devices.

VIDEO MODES

The settings in the Video Modes menu are used to fine-tune the picture, if necessary, after making all adjustments on the video display. It is recommended that you leave the settings at their defaults. See the Advanced Functions section for detailed information.

HEADPHONES

Plug the 1/4-inch plug on a pair of headphones into the front-panel jack for private listening. The default Headphone Bypass mode delivers a conventional 2-channel signal to the headphones.

Press the Surround Modes Button on the front panel or the remote, to switch to Harman Headphone virtual surround processing, which emulates a 5.1-channel speaker system. No other surround modes are available for the headphones.

USING THE RADIO

To select the AVR 2600’s built-in radio:

1.Press the Source List Button on the front panel. Use the 5/1 Buttons to scroll to the desired band.

2.Press the Radio Source Selector on the remote. Press it again to switch bands (AM, FM or SIRIUS).

A screen similar to the one shown in Figure 28 will appear. The SIRIUS band uses a different screen.

Figure 28 – FM Radio

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents AVR Service Instructions Outdoor Use Marking Safety InformationImportant Safety Instructions Wet Location MarkingImportant Safety Information UnpackingTable of Contents Introduction Surround ModesAudio/Video Inputs Supplied AccessoriesAudio Inputs Digital Audio InputsFront PanelControls On When the AVR is turned on, this LED turns white Volume Knob Turn this knob to raise or lower the volumeFRONT-PANEL Controls Connections RearREAR-PANEL Connections Use an HDMI-to-DVI adapterAlways make a separate audio connection AM and FM Antenna Terminals Connect the included Main Remote Control Functions AVR Power Off Button Press to turn off the AVR Surround Modes Press to directly access the SurroundMain Remote Control Functions Introduction to Home Theater Typical Home Theater SystemMultichannel Audio Subwoofer Connecting Source Devices to the AVRSpeaker Connections Audio ConnectionsDigital Video Video ConnectionsAnalog Audio Analog VideoAntennas USB PortPlacement of Surround Speakers in a 5.1-Channel System Speaker PlacementFront Speaker Placement Subwoofer PlacementGetting Started Source Assignment WorksheetGame Media Server Getting Started Installation Plug the AC Power cord into an unswitched AC outlet Step Nine Install a Multizone SystemStep TEN Plug in AC Power Cords Step SIX Connect AM AntennaStep Twelve Program Sources Into the Remote Step Thirteen Turn On the AVRTwo steps are required the first time you turn on the AVR Initial Setup Using the ON-SCREEN Menu SystemConfigure the AVR 2600, Using EzSet/EQ Technology Set Up Sources Audio and Video Input SelectionChannel Inputs You are now ready to begin enjoying your new receiver Dolby Volume Calibration Offset Volume ControlDolby Volume OperationUsing the Radio Sleep TimerHeadphones Mute FunctionSirius Satellite Radio Operation RecordingRemote Control Key Using Docking StationUsing The Bridge Previous TrackPlay Pause Menu Back/Exit or Left Arrow Select IPod Manual ModeSelecting a Surround Mode Right ArrowOperation Advanced Functions Analog Audio SignalsDigital Audio Signals Audio Processing and Surround SoundDolby Surround Settings Manual Speaker SetupVideo Game Logic 7 Game Step TWO Measure Speaker Distances Step Three Manual Setup MenuStep ONE Determine Speaker Crossover Number of SpeakersAdjust Crossover Frequencies Menu Adjust Speaker Distance MenuSub Mode Step Four Setting Channel Output Levels Manually Video AdjustmentsVideo Modes Video Modes MenuBrightness Adjustment System Settings General AVR SettingsSystem Information Advanced Remote Control FunctionsMenu Appearance Punch-Through ProgrammingMemory Resetting the RemoteProcessor Reset To program, or record an activity, follow these stepsTroubleshooting Guide Symptom Cause SolutionTable A2 Source Setting Defaults AppendixTable A1 Recommended Source Component Connections All Digital and 2-Channel Your Settings Analog Audio Inputs Table A3 Speaker/Channel Setting DefaultsTable A4 Delay Setting Defaults PositionDefault Table A5 Source SettingsTable A6 Audio Effects Settings Media Server Radio GameTable A8 Surround Modes Table A7 Video Modes SettingsBlack Level Off Deinterlacing Film Mode Detect Auto SelectTable A9 Remote Control Codes Table A10 System SettingsTable A11 Zone 2 Settings Surround Mode Description Incoming Bitstream or Signal Table A12 Surround ModesTable A12 Channel Stereo DTS 2/2/.0 or .1, 3/2/.0 orChannel music recordings Center speaker plays a summed mono mix36 37 38 40 41 Table A13 Remote Control Function List RadioTable A13 AUXTable A14 Remote Control Product Codes TV Table A15 Remote Control Product Codes AUX-HDTV Table A16 Remote Control Product Codes AUX-VCRTable A16 VCR Table A17 Remote Control Product Codes AUX-CD Table A18 Remote Control Product Codes DVDTable A17 CD Table A19 Remote Control Product Codes SAT Table A20 Remote Control Product Codes GameTable A21 Remote Control Product Codes Cable Table A24 Remote Control Product Codes AUX- TiVo Table A22 Remote Control Product Codes Media ServerTable A21 Cable AVR 2600 Technical Specifications Audio Section

AVR 2600 specifications

The Harman AVR 2600 is a feature-rich audio-video receiver designed to elevate your home entertainment experience. As part of Harman's renowned line of audio products, the AVR 2600 seamlessly combines advanced technology with user-friendly design, making it a popular choice for audiophiles and casual listeners alike.

One of the standout features of the AVR 2600 is its robust power output. With a rated 7.1 channel amplifier, it delivers a powerful and immersive sound experience. Each channel produces a significant amount of wattage, ensuring that your movies, music, and games sound spectacular and enveloping. This power enables the AVR 2600 to drive a variety of speaker configurations, allowing users to customize their sound setup according to their preferences.

In terms of connectivity, the Harman AVR 2600 boasts multiple HDMI inputs and outputs, supporting the latest video formats, including 4K. This allows users to connect multiple devices, such as gaming consoles, Blu-ray players, and streaming devices, all while maintaining a simple and clutter-free setup. The receiver also features built-in Bluetooth technology, enabling wireless streaming of music from smartphones, tablets, and other compatible devices. This versatility enhances the overall user experience, making it easy to access your favorite content.

The AVR 2600 also incorporates advanced audio processing technologies. With support for popular surround sound formats like Dolby Atmos and DTS:X, users can experience cinematic sound quality right in their living rooms. These technologies provide a three-dimensional audio experience, enhancing the immersion when watching movies or playing video games.

Another significant characteristic of the AVR 2600 is its user-friendly interface. Navigating the receiver is straightforward, thanks to the on-screen setup and intuitive remote control. The built-in setup assistant guides users through the calibration process, allowing for optimal speaker placement and sound adjustment based on the room's acoustics.

In conclusion, the Harman AVR 2600 is a powerful and versatile audio-video receiver that combines high-quality sound, advanced connectivity options, and user-friendly features. Whether you're looking to create the ultimate home theater experience or simply elevate your music listening, the AVR 2600 is an excellent choice that meets a wide range of entertainment needs.
Top Page Image Contents