Harman AVR 2600 owner manual Troubleshooting Guide, Symptom Cause Solution

Page 45

TROUBLESHOOTING GUIDE

Symptom

Cause

Solution

Unit does not function when Main

• No AC Power

• Make certain AC power cord is plugged into a live outlet

Power Switch is turned on

 

• Check whether outlet is switch-controlled

 

 

 

Display lights, but no sound

• Intermittent input connections

• Secure all input and speaker connections

or picture

• Mute is on

• Press Mute Button

 

• Volume control is down

• Turn up volume control

 

 

 

No sound from any speaker;

• Amplifier is in protection mode

• Check speaker wires for shorts at receiver and speaker ends

PROTECT message appears on

due to possible short

 

front panel

• Amplifier is in protection mode

• Contact your local Harman Kardon service center

 

due to internal problems

 

 

 

 

No sound from surround or

• Incorrect surround mode

• Select a mode other than Stereo

center speakers

• Input is monaural

• There is no surround information from mono sources

 

• Incorrect configuration

• Check speaker configuration

 

• Stereo or Mono program material

• The surround decoder may not create center- or rear-channel

 

 

information from nonencoded programs

 

 

 

Unit does not respond to

• Weak batteries in remote

• Change remote batteries

remote commands

• Wrong device selected

• Press the Setup Button

 

• Remote sensor is obscured

• Make certain front-panel sensor is in line of sight of remote

 

 

or connect an optional remote sensor

 

 

 

Intermittent buzzing in tuner

• Local interference

• Move unit or antenna away from computers, fluorescent

 

 

lights, motors or other electrical appliances

 

 

 

Surround Back Speaker settings

• Multizone system has been turned

• Use the menu system to access the Zone 2 menu. Turn off the Status

cannot be accessed, and test tone

on, and the surround back channels

setting to reassign the surround back channels to the main room.

does not play through Surround

were reassigned to multizone

 

Back Speakers

operation

 

 

 

 

The SIRIUS Preview Channel (001)

• SIRIUS tuner is not plugged in

• Use a SIRIUS tuner module designed for use with SIRIUS Ready home

is silent

 

audio equipment, and plug the module into the SIRIUS Radio Jack

 

• SIRIUS tuner is not located in such

• The SIRIUS tuner module needs an unobstructed view of the southern

 

a way as to enable reception

sky, or to be within range of a SIRIUS terrestrial repeater; if necessary,

 

 

purchase an extension cable from your SIRIUS Radio dealer

 

• SIRIUS signal requires a refresh

• Visit www.siriusradio.com

 

 

 

Unable to activate Program mode

• Source Selector not held for at

• The selector will light as you initially press it, and go dark as you

on remote

least 3 seconds

hold it down. Continue to hold it and wait 3 seconds for the selector

 

 

to light again

 

 

 

Remote buttons light, but AVR does

• Remote is in Zone 2 mode

• Slide the Zone Switch at the bottom of the remote to the

not respond

 

Zone 1 position

 

 

 

Additional information on troubleshooting possible problems with your AVR 2600, or installation-related issues, may be found in the list of “Frequently Asked Questions”, which is located in the Product Support section at www.harmankardon.com.

45

Page 44 Page 46
Image 45
Page 44 Page 46
Contents AVR Important Safety Instructions Safety InformationService Instructions Outdoor Use Marking Wet Location MarkingUnpacking Important Safety InformationTable of Contents Surround Modes IntroductionAudio Inputs Supplied AccessoriesAudio/Video Inputs Digital Audio InputsFront PanelControls On When the AVR is turned on, this LED turns white Volume Knob Turn this knob to raise or lower the volumeFRONT-PANEL Controls Rear ConnectionsREAR-PANEL Connections Use an HDMI-to-DVI adapterAlways make a separate audio connection AM and FM Antenna Terminals Connect the included Main Remote Control Functions Surround Modes Press to directly access the Surround AVR Power Off Button Press to turn off the AVRMain Remote Control Functions Introduction to Home Theater Typical Home Theater SystemMultichannel Audio Speaker Connections Connecting Source Devices to the AVRSubwoofer Audio ConnectionsAnalog Audio Video ConnectionsDigital Video Analog VideoUSB Port AntennasFront Speaker Placement Speaker PlacementPlacement of Surround Speakers in a 5.1-Channel System Subwoofer PlacementGetting Started Source Assignment WorksheetGame Media Server Getting Started Installation Step TEN Plug in AC Power Cords Step Nine Install a Multizone SystemPlug the AC Power cord into an unswitched AC outlet Step SIX Connect AM AntennaStep Twelve Program Sources Into the Remote Step Thirteen Turn On the AVRTwo steps are required the first time you turn on the AVR Initial Setup Using the ON-SCREEN Menu SystemConfigure the AVR 2600, Using EzSet/EQ Technology Audio and Video Input Selection Set Up SourcesChannel Inputs You are now ready to begin enjoying your new receiver Dolby Volume Volume ControlDolby Volume Calibration Offset OperationHeadphones Sleep TimerUsing the Radio Mute FunctionRecording Sirius Satellite Radio OperationUsing The Bridge Using Docking StationRemote Control Key Previous TrackSelecting a Surround Mode IPod Manual ModePlay Pause Menu Back/Exit or Left Arrow Select Right ArrowOperation Digital Audio Signals Analog Audio SignalsAdvanced Functions Audio Processing and Surround SoundDolby Surround Settings Manual Speaker SetupVideo Game Logic 7 Game Step ONE Determine Speaker Crossover Step Three Manual Setup MenuStep TWO Measure Speaker Distances Number of SpeakersAdjust Crossover Frequencies Menu Adjust Speaker Distance MenuSub Mode Video Adjustments Step Four Setting Channel Output Levels ManuallyVideo Modes Menu Video ModesBrightness Adjustment General AVR Settings System SettingsMenu Appearance Advanced Remote Control FunctionsSystem Information Punch-Through ProgrammingProcessor Reset Resetting the RemoteMemory To program, or record an activity, follow these stepsSymptom Cause Solution Troubleshooting GuideTable A2 Source Setting Defaults AppendixTable A1 Recommended Source Component Connections Table A4 Delay Setting Defaults Table A3 Speaker/Channel Setting DefaultsAll Digital and 2-Channel Your Settings Analog Audio Inputs PositionTable A6 Audio Effects Settings Table A5 Source SettingsDefault Media Server Radio GameBlack Level Off Deinterlacing Film Mode Detect Table A7 Video Modes SettingsTable A8 Surround Modes Auto SelectTable A9 Remote Control Codes Table A10 System SettingsTable A11 Zone 2 Settings Table A12 Surround Modes Surround Mode Description Incoming Bitstream or SignalTable A12 Channel music recordings DTS 2/2/.0 or .1, 3/2/.0 orChannel Stereo Center speaker plays a summed mono mix36 37 38 40 41 Radio Table A13 Remote Control Function ListAUX Table A13Table A14 Remote Control Product Codes TV Table A15 Remote Control Product Codes AUX-HDTV Table A16 Remote Control Product Codes AUX-VCRTable A16 VCR Table A17 Remote Control Product Codes AUX-CD Table A18 Remote Control Product Codes DVDTable A17 CD Table A19 Remote Control Product Codes SAT Table A20 Remote Control Product Codes GameTable A21 Remote Control Product Codes Cable Table A24 Remote Control Product Codes AUX- TiVo Table A22 Remote Control Product Codes Media ServerTable A21 Cable Audio Section AVR 2600 Technical Specifications

AVR 2600 specifications

The Harman AVR 2600 is a feature-rich audio-video receiver designed to elevate your home entertainment experience. As part of Harman's renowned line of audio products, the AVR 2600 seamlessly combines advanced technology with user-friendly design, making it a popular choice for audiophiles and casual listeners alike.

One of the standout features of the AVR 2600 is its robust power output. With a rated 7.1 channel amplifier, it delivers a powerful and immersive sound experience. Each channel produces a significant amount of wattage, ensuring that your movies, music, and games sound spectacular and enveloping. This power enables the AVR 2600 to drive a variety of speaker configurations, allowing users to customize their sound setup according to their preferences.

In terms of connectivity, the Harman AVR 2600 boasts multiple HDMI inputs and outputs, supporting the latest video formats, including 4K. This allows users to connect multiple devices, such as gaming consoles, Blu-ray players, and streaming devices, all while maintaining a simple and clutter-free setup. The receiver also features built-in Bluetooth technology, enabling wireless streaming of music from smartphones, tablets, and other compatible devices. This versatility enhances the overall user experience, making it easy to access your favorite content.

The AVR 2600 also incorporates advanced audio processing technologies. With support for popular surround sound formats like Dolby Atmos and DTS:X, users can experience cinematic sound quality right in their living rooms. These technologies provide a three-dimensional audio experience, enhancing the immersion when watching movies or playing video games.

Another significant characteristic of the AVR 2600 is its user-friendly interface. Navigating the receiver is straightforward, thanks to the on-screen setup and intuitive remote control. The built-in setup assistant guides users through the calibration process, allowing for optimal speaker placement and sound adjustment based on the room's acoustics.

In conclusion, the Harman AVR 2600 is a powerful and versatile audio-video receiver that combines high-quality sound, advanced connectivity options, and user-friendly features. Whether you're looking to create the ultimate home theater experience or simply elevate your music listening, the AVR 2600 is an excellent choice that meets a wide range of entertainment needs.
Top Page Image Contents