Husqvarna YTH2448 manual Tractor, Blade Removal See Fig, To Sharpen Blade See Fig

Page 17

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than fi ve (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See“PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent fl at tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OP- ERATION SYSTEM (ROS)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without fi rst setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch en- gaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

ROS "ON" POSITION

ENGINE "ON" POSITION

 

(NORMAL OPERATING)

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not ap- proved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 13)

•Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new or resharpened blade with stamped "THIS SIDE UP" facing deck and mandrel assembly.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: SPECIAL BLADE BOLT HEAT TREATED.

TO SHARPEN BLADE (See Fig. 14)

NOTE: We do not recommend sharpening blade - but if

BLADE

CENTER

 

MANDREL

 

 

 

 

ASSEMBLY

 

HOLE

 

 

 

 

BLADE BOLT

 

02544

STAR

(SPECIAL)

 

 

 

 

 

FIG. 13

828

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents YTH2448 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Steering Wheel Mower Unassembled PartsTools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See Figs Check Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Using the Reverse Operation SystemReverse Operation System ROS To Operate on HillsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolineAutomatic Transmission Warm UP Mowing TipsMaintenance Schedule MaintenanceLubrication Chart General RecommendationsTo Sharpen Blade See Fig TractorBlade Removal See Fig Engine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Secondary Drive Belt See Fig To Replace Mower Drive BeltTo Check Brake Belt InstallationTo Replace Motion Drive Belt See Fig Belt RemovalFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment To Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Starter SchematicPage Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

YTH2448 specifications

The Husqvarna YTH2448 is a feature-rich riding lawn mower designed for homeowners seeking efficiency and ease of use in maintaining their lawns. This model is powered by a robust 24 HP Kohler engine, providing ample power to tackle a variety of grass types and terrains. The engine is designed for reliable starts and improved fuel efficiency, ensuring that even the most demanding mowing tasks can be completed without interruption.

One of the standout features of the YTH2448 is its 48-inch cutting deck. This wide deck allows users to cover more ground in less time, making it ideal for medium to large-sized lawns. The cutting height can be easily adjusted with a lever, offering six different height settings ranging from 1.5 inches to 4 inches. This flexibility allows users to achieve the desired cut while accommodating varying grass conditions.

In terms of technology, the YTH2448 is equipped with a hydrostatic transmission that offers smooth and hassle-free operation. The automatic transmission enables users to control the speed without manual shifting, providing an enjoyable mowing experience. The articulated steering ensures tighter turning capabilities, allowing for better maneuverability around trees, flower beds, and other obstacles, reducing the need for trimming.

Comfort is another key aspect of the Husqvarna YTH2448. The spacious seating is ergonomically designed, providing support during prolonged use, and the easy-to-reach controls enhance the user experience. Additionally, the mower features a reinforced deck construction that enhances durability while also ensuring a clean cut.

For added convenience, the Husqvarna YTH2448 comes with a cutting deck washout port, making it simple to clean the mower after use. This feature helps maintain the performance of the mower while minimizing the buildup of grass clippings and debris that can impede cutting efficiency.

The YTH2448 also provides users with the option to add accessories, such as baggers and mulching kits, to customize their mowing experience. Whether your goal is to collect clippings for composting or create nutrient-rich mulch for your lawn, this mower can adapt to your needs.

In summary, the Husqvarna YTH2448 is a powerful, versatile, and user-friendly riding mower that combines strength, technology, and comfort, making it an excellent choice for homeowners looking to maintain a healthy and well-kept lawn. Its thoughtful engineering reflects Husqvarna's commitment to providing quality outdoor power equipment that enhances the mowing experience.
Top Page Image Contents