Husqvarna YTH2448 manual Storage, Other, Fuel System, Engine OIL, Cylinders

Page 26

STORAGE

Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more.

WARNING: Never store the tractor with gasoline in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any enclosure.

TRACTOR

Remove mower from tractor for winter storage. When mower is to be stored for a period of time, clean it thoroughly, remove all dirt, grease, leaves, etc. Store in a clean, dry area.

•Clean entire tractor (See “CLEANING” in the Mainte- nance section of this manual).

•Inspect and replace belts, if necessary (See belt re- placement instructions in the Service and Adjustments section of this manual).

•Lubricate as shown in the Maintenance section of this manual.

•Be sure that all nuts, bolts and screws are securely fastened. Inspect moving parts for damage, breakage and wear. Replace if necessary.

•Touch up all rusted or chipped paint surfaces; sand lightly before painting.

BATTERY

•Fully charge the battery for storage.

•After a period of time in storage, battery may require recharging.

•To help prevent corrosion and power leakage during long periods of storage, battery cables should be dis- connected and battery cleaned thoroughly (see “TO CLEAN BATTERY AND TERMINALS” in the Mainte- nance section of this manual).

•After cleaning, leave cables disconnected and place cables where they cannot come in contact with battery terminals.

•If battery is removed from tractor for storage, do not store battery directly on concrete or damp surfaces.

ENGINE

FUEL SYSTEM

IMPORTANT: IT IS IMPORTANTTO PREVENT GUM DEPOSITS FROM FORMING IN ESSENTIAL FUEL SYSTEM PARTS SUCH AS CARBURETOR, FUEL FILTER, FUEL HOSE, OR TANK DURING STORAGE. ALSO, EXPERIENCE INDICATES THAT ALCOHOL BLENDED FUELS (CALLED GASOHOL OR USING ETHANOL OR METHANOL) CAN ATTRACT MOISTUREWHICH LEADSTO SEPARATION AND FORMATION OF ACIDS DURING STORAGE. ACIDIC GAS CAN DAMAGE THE FUEL SYSTEM OF AN ENGINE WHILE IN STORAGE.

•Empty the fuel tank by starting the engine and let it run until the fuel lines and carburetor are empty.

•Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

•Use fresh fuel next season.

NOTE: Fuel stabilizer is an acceptable alternative in mini- mizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or storage container. Always follow the mix ratio found on stabilizer container. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Do not empty the gas tank and carburetor if using fuel stabilizer.

ENGINE OIL

Drain oil (with engine warm) and replace with clean en- gine oil. (See “ENGINE” in the Maintenance section of this manual).

CYLINDER(S)

•Remove spark plug(s).

•Pour one ounce of oil through spark plug hole(s) into cylinder(s).

•Turn ignition key to “START” position for a few seconds to distribute oil.

•Replace with new spark plug(s).

OTHER

•Do not store gasoline from one season to another.

•Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems.

•If possible, store your tractor indoors and cover it to give protection from dust and dirt.

•Cover your tractor with a suitable protective cover that does not retain moisture. Do not use plastic. Plastic cannot breathe which allows condensation to form and will cause your tractor to rust.

IMPORTANT: NEVER COVERTRACTORWHILE ENGINE AND EXHAUST AREAS ARE STILL WARM.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents YTH2448 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Steering Wheel MowerTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See Figs Check for Proper Position of ALL Belts Check Tire PressureCheck Mower Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS Using the Reverse Operation SystemTo Operate Mower See Fig To Operate on HillsCheck Engine OIL Level Before Starting the EngineTowing Carts and Other ATTACH- Ments ADD GasolineMowing Tips Automatic Transmission Warm UPLubrication Chart MaintenanceMaintenance Schedule General RecommendationsTo Sharpen Blade See Fig TractorBlade Removal See Fig Engine Cleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Drive Belt To Replace Mower Blade Secondary Drive Belt See FigTo Replace Motion Drive Belt See Fig Belt InstallationTo Check Brake Belt RemovalFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment To Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic StarterPage Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

YTH2448 specifications

The Husqvarna YTH2448 is a feature-rich riding lawn mower designed for homeowners seeking efficiency and ease of use in maintaining their lawns. This model is powered by a robust 24 HP Kohler engine, providing ample power to tackle a variety of grass types and terrains. The engine is designed for reliable starts and improved fuel efficiency, ensuring that even the most demanding mowing tasks can be completed without interruption.

One of the standout features of the YTH2448 is its 48-inch cutting deck. This wide deck allows users to cover more ground in less time, making it ideal for medium to large-sized lawns. The cutting height can be easily adjusted with a lever, offering six different height settings ranging from 1.5 inches to 4 inches. This flexibility allows users to achieve the desired cut while accommodating varying grass conditions.

In terms of technology, the YTH2448 is equipped with a hydrostatic transmission that offers smooth and hassle-free operation. The automatic transmission enables users to control the speed without manual shifting, providing an enjoyable mowing experience. The articulated steering ensures tighter turning capabilities, allowing for better maneuverability around trees, flower beds, and other obstacles, reducing the need for trimming.

Comfort is another key aspect of the Husqvarna YTH2448. The spacious seating is ergonomically designed, providing support during prolonged use, and the easy-to-reach controls enhance the user experience. Additionally, the mower features a reinforced deck construction that enhances durability while also ensuring a clean cut.

For added convenience, the Husqvarna YTH2448 comes with a cutting deck washout port, making it simple to clean the mower after use. This feature helps maintain the performance of the mower while minimizing the buildup of grass clippings and debris that can impede cutting efficiency.

The YTH2448 also provides users with the option to add accessories, such as baggers and mulching kits, to customize their mowing experience. Whether your goal is to collect clippings for composting or create nutrient-rich mulch for your lawn, this mower can adapt to your needs.

In summary, the Husqvarna YTH2448 is a powerful, versatile, and user-friendly riding mower that combines strength, technology, and comfort, making it an excellent choice for homeowners looking to maintain a healthy and well-kept lawn. Its thoughtful engineering reflects Husqvarna's commitment to providing quality outdoor power equipment that enhances the mowing experience.
Top Page Image Contents