Husqvarna YTH2448 manual To Replace Mower Drive Belt

Page 22

SERVICE AND ADJUSTMENTS

TO REPLACE MOWER DRIVE BELT

MOWER DRIVE BELT REMOVAL (See Fig. 23)

Park tractor on a level surface. Engage parking brake.

Lower mower to its lowest position.

Remove screws from R.H. mandrel cover and remove cover.

Remove any dirt or grass clippings which may have accumulated around mandrels and entire upper deck surface.

Disconnect R.H.suspension arm from rear deck bracket by removing retainer spring.

Roll belt over the top of R.H. mandrel pulley carefully.

Remove belt from electric clutch pulley.

Remove belt from idler pulleys.

Check primary idler arm and two idlers to see that they rotate freely.

Be sure spring is securely hooked to primary idler arm and spring arm.

MOWER DRIVE BELT INSTALLATION (See Fig. 23)

Install belt in both idlers.

Install new belt onto electric clutch pulley.

Roll belt into upper groove of R.H. mandrel pulley care- fully.

Carefully check belt routing making sure belt is in the grooves correctly.

Reconnect R.H. suspension arm to rear deck bracket with retainer spring.

Reassemble R.H. mandrel cover.

RH MANDREL

 

COVER

ELECTRIC

 

CLUTCH

 

PULLEY

 

IDLER

 

PULLEYS

SPRING ARM

 

RH SUSPENSION

 

ARM

 

PRIMARY IDLER ARM

02514

R.H. MANDREL

 

FIG. 23

TO REPLACE MOWER BLADE (SECONDARY) DRIVE BELT (See Fig. 24)

Park the tractor on level surface. Engage parking brake.

Remove mower (See “TO REMOVE MOWER” in this section of manual).

Remove screws from R.H. and L.H. mandrel covers and remove covers.

REMOVE MOWER DRIVE BELT

(Refer to “TO REMOVE MOWER DRIVE BELT” illustration in this section of manual).

Carefully roll belt over the top of R.H. mandrel pulley.

Remove belt from idler pulleys.

Check primary idler arm and two idlers to see that they rotate freely.

Be sure spring is securely hooked to primary idler arm and spring arm.

REMOVE MOWER BLADE (SECONDARY) DRIVE BELT

Carefully roll belt off L.H. mandrel pulley.

Remove belt from center mandrel pulley, idler pulley, and R.H. mandrel pulley.

Remove any dirt or grass which may have accumulated around mandrels and entire upper deck surface.

Check secondary idler arm and idler pulley to see that they rotate freely.

Be sure spring is hooked in secondary idler arm and secondary spring arm.

INSTALL NEW MOWER BLADE (SECONDARY) DRIVE BELT

Install new belt in lower groove of R.H. mandrel pulley, idler pulley, and center mandrel pulley as shown.

Carefully roll belt over L.H. mandrel pulley. Make sure belt is in all grooves properly.

REINSTALL MOWER DRIVE BELT

(Refer to “TO REMOVE MOWER DRIVE BELT” illustration in this section of manual).

Install belt into upper groove of R.H. mandrel pulley and around both idlers. Pull belt to front of mower to remove slack.

Reinstall mandrel covers and securely tighten all screws.

Carefully check belt routing making sure belt is in all grooves correctly.

Reinstall mower to tractor (See “TO INSTALL MOWER” in this section of manual).

L.H. MANDREL

SECONDARY

 

IDLER ARM

 

SPRING

 

SECONDARY

 

SPRING ARM

 

CENTER

 

MANDREL

IDLER

PULLEY

R.H. MANDREL

02515

 

FIG. 24

22

Image 22
Contents YTH2448 General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts Steering Wheel MowerTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidTo Attach Nose Roller See Fig Install Seat See FigAssemble Gauge Wheels to Mower Deck See Fig Install Mower and Drive Belt See Figs Check for Proper Position of ALL Belts Check Tire PressureCheck Mower Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS Using the Reverse Operation SystemTo Operate Mower See Fig To Operate on HillsCheck Engine OIL Level Before Starting the EngineTowing Carts and Other ATTACH- Ments ADD GasolineMowing Tips Automatic Transmission Warm UPLubrication Chart MaintenanceMaintenance Schedule General RecommendationsBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine Cleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Replace Mower Drive Belt To Replace Mower Blade Secondary Drive Belt See FigTo Replace Motion Drive Belt See Fig Belt InstallationTo Check Brake Belt RemovalTo Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN/CAMBER To Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Schematic StarterPage Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

YTH2448 specifications

The Husqvarna YTH2448 is a feature-rich riding lawn mower designed for homeowners seeking efficiency and ease of use in maintaining their lawns. This model is powered by a robust 24 HP Kohler engine, providing ample power to tackle a variety of grass types and terrains. The engine is designed for reliable starts and improved fuel efficiency, ensuring that even the most demanding mowing tasks can be completed without interruption.

One of the standout features of the YTH2448 is its 48-inch cutting deck. This wide deck allows users to cover more ground in less time, making it ideal for medium to large-sized lawns. The cutting height can be easily adjusted with a lever, offering six different height settings ranging from 1.5 inches to 4 inches. This flexibility allows users to achieve the desired cut while accommodating varying grass conditions.

In terms of technology, the YTH2448 is equipped with a hydrostatic transmission that offers smooth and hassle-free operation. The automatic transmission enables users to control the speed without manual shifting, providing an enjoyable mowing experience. The articulated steering ensures tighter turning capabilities, allowing for better maneuverability around trees, flower beds, and other obstacles, reducing the need for trimming.

Comfort is another key aspect of the Husqvarna YTH2448. The spacious seating is ergonomically designed, providing support during prolonged use, and the easy-to-reach controls enhance the user experience. Additionally, the mower features a reinforced deck construction that enhances durability while also ensuring a clean cut.

For added convenience, the Husqvarna YTH2448 comes with a cutting deck washout port, making it simple to clean the mower after use. This feature helps maintain the performance of the mower while minimizing the buildup of grass clippings and debris that can impede cutting efficiency.

The YTH2448 also provides users with the option to add accessories, such as baggers and mulching kits, to customize their mowing experience. Whether your goal is to collect clippings for composting or create nutrient-rich mulch for your lawn, this mower can adapt to your needs.

In summary, the Husqvarna YTH2448 is a powerful, versatile, and user-friendly riding mower that combines strength, technology, and comfort, making it an excellent choice for homeowners looking to maintain a healthy and well-kept lawn. Its thoughtful engineering reflects Husqvarna's commitment to providing quality outdoor power equipment that enhances the mowing experience.