Husqvarna YTH2448 manual To Level Mower Housing, FRONT-TO-BACK Adjustment See Figs

Page 21

SERVICE AND ADJUSTMENTS

•Position front plate assembly between front mower brackets. Raise deck and plate assembly to align holes and insert fl anged pins. Secure pins with double loop retainer springs between the plate and mower brack- ets.

NOTE: To assist in locating hole in fl anged pin, the hole in pin is inline with notch on head of pin. If necessary, move mower side-to-side to give space between plate and mower brackets.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

•Connect anti-sway bar to chassis bracket under left footrest and retain with double loop retainer spring.

•If equipped, turn height adjustment knob clockwise to remove slack from mower suspension.

•Raise deck to highest position.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly infl ated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinfl ated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 19 and 20)

•Raise mower to its highest position.

•Measure height from bottom edge of mower to ground level at front corners of mower. Distance “A” on both sides of mower should be the same.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

00598

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 19

SUSPENSION

ARM

01553

LIFT LINK

ADJUSTMENT NUT

FIG. 20

FRONT-TO-BACK ADJUSTMENT (See Figs. 21 and 22)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is approximately 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

Check adjustment on right side of tractor. Position any blade so the tip is pointing straight forward. Measure distance "B" at front and rear tip of the blade.

•Before making any necessary adjustments, check that both front plate links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of blade, loosen nut “C” on both front links an equal number of turns.

NOTE: Each full turn of nut “C” will change distance. “B” by approximately 3/16".

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•To raise front of blade, loosen nut “D” from trunnion on both front links. Tighten nut “C” on both front links an equal number of turns.The two front links must remain equal in length.

•When distance “B” is 1/8" to 1/2" lower at front than rear, tighten nut “D” against trunnion on both front links.

•Recheck side-to-side adjustment.

BLADE

02548

“B”“B”

FIG. 21

BOTH FRONT PLATE LINKS MUST BE

 

EQUAL IN LENGTH

 

 

02516

 

NUT “D”

 

NUT “C”

 

02517

TRUNNION

 

 

FRONT PLATE

 

 

ASSEMBLY

 

 

FIG. 22

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents YTH2448 Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Steering Wheel Mower Unassembled PartsTools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidInstall Seat See Fig To Attach Nose Roller See FigAssemble Gauge Wheels to Mower Deck See Fig Install Mower and Drive Belt See Figs Check Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Using the Reverse Operation SystemReverse Operation System ROS To Operate on HillsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolineAutomatic Transmission Warm UP Mowing TipsMaintenance Schedule MaintenanceLubrication Chart General RecommendationsTractor Blade Removal See FigTo Sharpen Blade See Fig Engine Cleaning Service and Adjustments To Install MowerTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Secondary Drive Belt See Fig To Replace Mower Drive BeltTo Check Brake Belt InstallationTo Replace Motion Drive Belt See Fig Belt RemovalTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER To Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Starter SchematicPage Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

YTH2448 specifications

The Husqvarna YTH2448 is a feature-rich riding lawn mower designed for homeowners seeking efficiency and ease of use in maintaining their lawns. This model is powered by a robust 24 HP Kohler engine, providing ample power to tackle a variety of grass types and terrains. The engine is designed for reliable starts and improved fuel efficiency, ensuring that even the most demanding mowing tasks can be completed without interruption.

One of the standout features of the YTH2448 is its 48-inch cutting deck. This wide deck allows users to cover more ground in less time, making it ideal for medium to large-sized lawns. The cutting height can be easily adjusted with a lever, offering six different height settings ranging from 1.5 inches to 4 inches. This flexibility allows users to achieve the desired cut while accommodating varying grass conditions.

In terms of technology, the YTH2448 is equipped with a hydrostatic transmission that offers smooth and hassle-free operation. The automatic transmission enables users to control the speed without manual shifting, providing an enjoyable mowing experience. The articulated steering ensures tighter turning capabilities, allowing for better maneuverability around trees, flower beds, and other obstacles, reducing the need for trimming.

Comfort is another key aspect of the Husqvarna YTH2448. The spacious seating is ergonomically designed, providing support during prolonged use, and the easy-to-reach controls enhance the user experience. Additionally, the mower features a reinforced deck construction that enhances durability while also ensuring a clean cut.

For added convenience, the Husqvarna YTH2448 comes with a cutting deck washout port, making it simple to clean the mower after use. This feature helps maintain the performance of the mower while minimizing the buildup of grass clippings and debris that can impede cutting efficiency.

The YTH2448 also provides users with the option to add accessories, such as baggers and mulching kits, to customize their mowing experience. Whether your goal is to collect clippings for composting or create nutrient-rich mulch for your lawn, this mower can adapt to your needs.

In summary, the Husqvarna YTH2448 is a powerful, versatile, and user-friendly riding mower that combines strength, technology, and comfort, making it an excellent choice for homeowners looking to maintain a healthy and well-kept lawn. Its thoughtful engineering reflects Husqvarna's commitment to providing quality outdoor power equipment that enhances the mowing experience.
Top Page Image Contents