Husqvarna YTH2448 manual Install Seat See Fig, To Attach Nose Roller See Fig

Page 7

ASSEMBLY

INSTALL SEAT (See Fig. 3)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and fl at washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

SEAT SHOULDER

BOLT

SEAT PAN

466

FLAT WASHER

ADJUSTMENT

02464

KNOB

 

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place freewheel control in "transmission disengaged position" (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place motion control lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine.After engine has started, move throttle control to idle position.

•Release parking brake.

•Slowly move the motion control lever forward and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

TO ATTACH NOSE ROLLER (See Fig. 4)

•Assemble brackets "A" and "B" to the inside of mower mounting brackets as shown. Tighten securely.

NOTE: Be sure bracket tabs are positioned in tab holes in mower brackets.

•Position nose roller between brackets and install rod and retainer spring.

 

LOCK

HEX

ROD

 

BOLT

 

 

 

NUT

 

 

 

 

 

"B"

 

 

 

BRACKET

TAB

 

 

 

HOLE

 

 

 

RETAINER

02612

 

NOSE

 

 

SPRING

"A" BRACKET

 

ROLLER

FIG. 4

ASSEMBLE GAUGE WHEELS TO MOWER DECK (See Fig. 5)

The gauge wheels are designed to keep the mower deck in proper position when operating mower. Be sure they are properly adjusted to ensure optimum mower perfor- mance.

•Slide gauge wheel bar down into bracket channel, Be sure that gauge wheel bar aligning holes are on top. Assemble gauge wheels as shown using shoulder bolts, 3/8 washers and 3/8-16 center locknuts and tighten securely.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents YTH2448 II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Steering Wheel Mower Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonTo Attach Nose Roller See Fig Install Seat See FigAssemble Gauge Wheels to Mower Deck See Fig Install Mower and Drive Belt See Figs Check Brake System Check Tire PressureCheck Mower Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Using the Reverse Operation SystemTo Operate Mower See Fig Reverse Operation System ROSADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelAutomatic Transmission Warm UP Mowing TipsGeneral Recommendations MaintenanceMaintenance Schedule Lubrication ChartBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine Cleaning To Install Mower Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Secondary Drive Belt See Fig To Replace Mower Drive BeltBelt Removal Belt InstallationTo Check Brake To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN/CAMBER To Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Starter SchematicPage Suggested Guide for Sighting Slopes for Safe Operation Warranty Statement

YTH2448 specifications

The Husqvarna YTH2448 is a feature-rich riding lawn mower designed for homeowners seeking efficiency and ease of use in maintaining their lawns. This model is powered by a robust 24 HP Kohler engine, providing ample power to tackle a variety of grass types and terrains. The engine is designed for reliable starts and improved fuel efficiency, ensuring that even the most demanding mowing tasks can be completed without interruption.

One of the standout features of the YTH2448 is its 48-inch cutting deck. This wide deck allows users to cover more ground in less time, making it ideal for medium to large-sized lawns. The cutting height can be easily adjusted with a lever, offering six different height settings ranging from 1.5 inches to 4 inches. This flexibility allows users to achieve the desired cut while accommodating varying grass conditions.

In terms of technology, the YTH2448 is equipped with a hydrostatic transmission that offers smooth and hassle-free operation. The automatic transmission enables users to control the speed without manual shifting, providing an enjoyable mowing experience. The articulated steering ensures tighter turning capabilities, allowing for better maneuverability around trees, flower beds, and other obstacles, reducing the need for trimming.

Comfort is another key aspect of the Husqvarna YTH2448. The spacious seating is ergonomically designed, providing support during prolonged use, and the easy-to-reach controls enhance the user experience. Additionally, the mower features a reinforced deck construction that enhances durability while also ensuring a clean cut.

For added convenience, the Husqvarna YTH2448 comes with a cutting deck washout port, making it simple to clean the mower after use. This feature helps maintain the performance of the mower while minimizing the buildup of grass clippings and debris that can impede cutting efficiency.

The YTH2448 also provides users with the option to add accessories, such as baggers and mulching kits, to customize their mowing experience. Whether your goal is to collect clippings for composting or create nutrient-rich mulch for your lawn, this mower can adapt to your needs.

In summary, the Husqvarna YTH2448 is a powerful, versatile, and user-friendly riding mower that combines strength, technology, and comfort, making it an excellent choice for homeowners looking to maintain a healthy and well-kept lawn. Its thoughtful engineering reflects Husqvarna's commitment to providing quality outdoor power equipment that enhances the mowing experience.
Top Page Image Contents