Husqvarna YTH2242TDF To Move Forward and Backward See Fig, To USE Cruise Control J See Fig

Page 10

OPERATION

TO MOVE FORWARD AND BACKWARD (See Fig. 7)

The direction and speed of movement is controlled by the forward and reverse drive pedals.

•Start tractor and release parking brake.

•Slowly depress forward (K) or reverse (L) drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.

K

J

L

Fig. 7

TO USE CRUISE CONTROL (J) (See Fig. 7)

The cruise control feature can be used for forward travel only.

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 8)

The position of the attachment lift lever (A) determines the cutting height.

A

Fig. 8

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in this section of manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole. Tighten securely.

•Repeat for all, installing gauge wheel in same adjust- ment hole.

Fig. 9

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut (see "TO ADJUST MOWER CUTTING HEIGHT")

•Start mower blades by engaging attachment clutch control.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents YTH2242TDF General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyTools Required for Assembly ToremovetractorfromcartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor CJKTo SET Parking BRAKESee Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged Stopping See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigTo Operate on Hills To Stop Mower BladesReverse Operation System ROS To Transport See FigCheck Engine OIL Level Service REMINDER/HOUR MeterBefore Starting the Engine ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP General Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningDeck Washout Port See Fig To Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig Raise attachment lift lever to highest position To Level Mower To Replace Mower Blade Drive Belt To Check BrakeFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Replace Motion Drive Belt See Fig To Remove Wheel for Repairs See FigTransmission Fuel System StorageOther Engine OILTroubleshooting Problem Cause CorrectionFires when turn To run when operBattery will not Engine continuesSchematic SCH12Electrical KEY Part Description 196 Chassis 207 Drive Spark Arrester KIT EngineEngine Power Rating Information Steering Assembly 532 41 Wheel, Steering Seat Assembly 532 42 SeatDecals Wheels and TiresMower Deck Tractor Model NO. YTH2242TDF 96041017302, Product no 41 Mower Lift 532 40 34-07 Link Lift Susp Mower RearSuggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX12.01.10 CL/SR

YTH2242TDF specifications

The Husqvarna YTH2242TDF is a robust and reliable riding mower designed for homeowners seeking a machine that combines power, efficiency, and ease of use. Packed with essential features and advanced technologies, this mower stands out for its performance and versatility in tackling landscaping tasks.

One of the key features of the YTH2242TDF is its powerful 18.5 HP Briggs & Stratton engine. This durable engine ensures consistent performance, allowing users to navigate their lawns with ease. The Hydrostatic transmission further enhances this experience, providing a smooth and effortless driving experience without the need for manual gear changes. This user-friendly design enables operators of all skill levels to maneuver effectively and efficiently around their property.

The cutting deck of the YTH2242TDF measures 42 inches, making it suitable for medium to large sized lawns. This size allows for a wide cutting path, reducing the time needed to mow. The deck features a washing port, making maintenance a breeze by allowing users to easily clean the underside of the deck after mowing, helping to maintain optimal cutting efficiency.

Additionally, the mower is equipped with a compact design that provides excellent visibility and maneuverability in tight spaces. Its tight turning radius enables users to navigate landscaping features with precision, reducing the need for excessive trimming afterwards.

Another noteworthy attribute of the YTH2242TDF is its comfort features. The adjustable seat ensures that operators can find their ideal position, while ergonomic controls reduce fatigue during extended use. The easy-access controls are designed to enhance user comfort and efficiency, making the mowing experience more enjoyable.

For added versatility, the YTH2242TDF is compatible with a variety of attachments, including baggers, plows, and mulchers, making it an excellent investment for seasonal tasks beyond mowing. This flexibility allows users to maximize the utility of their mower throughout the year.

In terms of build quality, Husqvarna's commitment to durability is evident in the robust construction of the YTH2242TDF. The cutting deck is made from high-quality steel, ensuring it can withstand the rigors of regular use.

In summary, the Husqvarna YTH2242TDF is an exceptional choice for homeowners looking for a reliable, efficient, and easy-to-use riding mower. With its powerful engine, smooth transmission, and versatile design, it stands out as a valuable tool for maintaining beautiful lawns.
Top Page Image Contents