Husqvarna YTH2242TDF owner manual Cleaning, IN-LINE Fuel Filter See Fig, Deck Washout Port See Fig

Page 17

MAINTENANCE

IN-LINE FUEL FILTER (See Fig. 18)

The fuel filter should be replaced once each season. If fuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required.

•With engine cool, remove filter and plug fuel line sec- tions.

•Place new fuel filter in position in fuel line with arrow pointing towards carburetor.

•Be sure there are no fuel line leaks and clamps are properly positioned.

•Immediately wipe up any spilled gasoline.

CLAMP

FUEL FILTER

Fig. 18

CLEANING

•Clean engine, battery, seat, finish, etc. of all foreign matter.

•Clean debris from steering plate. Debris can restrict clutch/brake pedal shaft movement, causing belt slip and loss of drive.

CAUTION: Avoid all pinch points and movable parts (See Fig. 19)

CLUTCH/BRAKE PEDAL

CLEAN TOP SIDE

STEERING

PLATE

CAUTION:

PINCH

POINTS

STEERING SYSTEM,

DASH, FENDER AND

MOWER NOT SHOWN

Fig. 19

•Keep finished surfaces and wheels free of all gasoline, oil, etc.

•Protect painted surfaces with automotive type wax.

We do not recommend using a garden hose or pressure washer to clean your tractor unless the engine and trans- mission are covered to keep water out. Water in engine or transmission will shorten the useful life of your tractor. Use compressed air or a leaf blower to remove grass, leaves and trash from tractor and mower.

DECK WASHOUT PORT (See Fig. 20)

Your tractor’s deck is equipped with a washout port on its surface as part of its deck wash system. It should be utilized after each use.

1.Drive the tractor to a level, clear spot on your lawn, near enough to a water spigot for your garden hose to reach.

IMPORTANT: Make certain the tractor’s discharge chute is directed AWAY from your house, garage, parked cars, etc. Remove bagger chute or mulch cover if attached.

2.Make sure the attachment clutch control is in the “DISENGAGED” position, set the parking brake, and stop the engine.

3.Thread the nozzle adapter (packaged with your tractor’s Operator’s Manual) onto the end of your garden hose.

4.Pull back the lock collar of the nozzle adapter and push the adapter onto the deck washout port at the left end of the mower deck. Release the lock collar to lock the adapter on the nozzle.

HOSE

NOZZLE ADAPTER

WASHOUT PORT

Fig. 20

IMPORTANT: Tug hose ensuring connection is secure.

5.Turn the water on.

6.While sitting in the operator’s position on the tractor, re-start the engine and place the throttle lever in the Fast " " position.

IMPORTANT: Recheck the area making certain the area is clear.

7.Move the tractor’s attachment clutch control to the “EN- GAGED” position. Remain in the operator’s position with the cutting deck engaged until the deck is cleaned.

8.Move the tractor’s attachment clutch control to the “DISENGAGED” position. Turn the ignition key to the STOP position to turn the tractor’s engine off. Turn the water off.

9.Pull back the lock collar of the nozzle adapter to discon- nect the adapter from the nozzle washout port.

10.Move the tractor to a dry area, preferably a concrete or paved area. Place the attachment clutch control in the “ENGAGED” position to remove excess water and to help dry before putting the tractor away.

WARNING: A broken or missing washout fitting could expose you or others to thrownobjectsfromcontactwiththeblade.

•Replace broken or missing washout fitting immediately, prior to using mower again.

•Pluganyholesinmowerwithboltsandlocknuts.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents YTH2242TDF Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Tools Required for Assembly AssemblyUnassembled Parts ToremovetractorfromcartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation CJK Know Your TractorAttachment Clutch Switch Disengaged Engaged HOW to USE Your TractorTo SET Parking BRAKESee Fig Stopping See FigTo Adjust Gauge Wheels See Fig To Adjust Mower Cutting Height See FigTo Move Forward and Backward See Fig To USE Cruise Control J See FigReverse Operation System ROS To Stop Mower BladesTo Operate on Hills To Transport See FigBefore Starting the Engine Service REMINDER/HOUR MeterCheck Engine OIL Level ADD GasolineAutomatic Transmission Warm UP Mowing TipsPurge Transmission Maintenance MaintenanceGeneral Recommendations ScheduleTractor BatteryBlade Care Blade Removal See FigEngine Deck Washout Port See Fig CleaningIN-LINE Fuel Filter See Fig To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Figs Raise attachment lift lever to highest position To Level Mower To Check Brake To Replace Mower Blade Drive BeltTo Replace Motion Drive Belt See Fig To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTransmission Other StorageFuel System Engine OILProblem Cause Correction TroubleshootingBattery will not To run when operFires when turn Engine continuesSCH12 SchematicElectrical KEY Part Description 196 Chassis 207 Drive Engine Spark Arrester KITEngine Power Rating Information Steering Assembly 532 41 Wheel, Steering 532 42 Seat Seat AssemblyWheels and Tires DecalsMower Deck Tractor Model NO. YTH2242TDF 96041017302, Product no 41 532 40 34-07 Link Lift Susp Mower Rear Mower LiftOnly Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation12.01.10 CL/SR

YTH2242TDF specifications

The Husqvarna YTH2242TDF is a robust and reliable riding mower designed for homeowners seeking a machine that combines power, efficiency, and ease of use. Packed with essential features and advanced technologies, this mower stands out for its performance and versatility in tackling landscaping tasks.

One of the key features of the YTH2242TDF is its powerful 18.5 HP Briggs & Stratton engine. This durable engine ensures consistent performance, allowing users to navigate their lawns with ease. The Hydrostatic transmission further enhances this experience, providing a smooth and effortless driving experience without the need for manual gear changes. This user-friendly design enables operators of all skill levels to maneuver effectively and efficiently around their property.

The cutting deck of the YTH2242TDF measures 42 inches, making it suitable for medium to large sized lawns. This size allows for a wide cutting path, reducing the time needed to mow. The deck features a washing port, making maintenance a breeze by allowing users to easily clean the underside of the deck after mowing, helping to maintain optimal cutting efficiency.

Additionally, the mower is equipped with a compact design that provides excellent visibility and maneuverability in tight spaces. Its tight turning radius enables users to navigate landscaping features with precision, reducing the need for excessive trimming afterwards.

Another noteworthy attribute of the YTH2242TDF is its comfort features. The adjustable seat ensures that operators can find their ideal position, while ergonomic controls reduce fatigue during extended use. The easy-access controls are designed to enhance user comfort and efficiency, making the mowing experience more enjoyable.

For added versatility, the YTH2242TDF is compatible with a variety of attachments, including baggers, plows, and mulchers, making it an excellent investment for seasonal tasks beyond mowing. This flexibility allows users to maximize the utility of their mower throughout the year.

In terms of build quality, Husqvarna's commitment to durability is evident in the robust construction of the YTH2242TDF. The cutting deck is made from high-quality steel, ensuring it can withstand the rigors of regular use.

In summary, the Husqvarna YTH2242TDF is an exceptional choice for homeowners looking for a reliable, efficient, and easy-to-use riding mower. With its powerful engine, smooth transmission, and versatile design, it stands out as a valuable tool for maintaining beautiful lawns.
Top Page Image Contents