Husqvarna YTH2242TDF owner manual To Replace Motion Drive Belt See Fig, Front Wheel TOE-IN/CAMBER

Page 22

SERVICE AND ADJUSTMENTS

TO REPLACE MOTION DRIVE BELT (See Fig. 34)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

1.Remove mower (See “TO REMOVE MOWER” section in this manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

2.Disconnect clutch wire harness (A).

3.Remove anti-rotation link (B) on right side of tractor.

4.Removebeltfromstationaryidler(C)andclutchingidler(D).

5.Remove belt from centerspan idler (E).

6.Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades (F).

7.Remove belt downward from engine pulley and around electric clutch (G).

8.Slide belt toward rear of tractor, off the steering plate

(H) and remove from tractor.

BELT INSTALLATION -

1.Install new belt from tractor rear to front, over the steer- ing plate (H) and above clutch brake pedal shaft (J).

2.Pull belt toward front of tractor and roll belt around electric clutch and onto engine pulley (G).

3.Pull belt toward rear of tractor. Carefully work belt down around transmission cooling fan and onto the input pul- ley (F). Be sure belt is inside the belt keeper.

4.Install belt on centerspan idler (E).

5.Installbeltthroughstationaryidler(C)andclutchingidler(D).

6.Reinstall anti-rotation link (B) on right side of tractor. Tighten securely.

7.Reconnect clutch harness (A).

8.Make sure belt is in all pulley grooves and inside all belt guides and keepers.

9.Install mower (See “TO INSTALL MOWER” section in

FRONT WHEEL TOE-IN/CAMBER

Your new tractor front wheel toe-in and camber is set at the factory and is normal. The front wheel toe-in and camber are not adjustable. If damage has occurred to affect the factory set front wheel toe-in or camber, contact a qualified service center.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 35)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

Fig. 35

TO START ENGINE WITH A WEAK BATTERY (See Fig. 36)

this manual).

B A

G

H

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

 

C

D

J

 

E

F

02953 electric

Fig. 34

22

 

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

Page 21 Page 23
Image 22
Page 21 Page 23
Contents YTH2242TDF General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Unassembled Parts AssemblyTools Required for Assembly ToremovetractorfromcartonCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor CJKTo SET Parking BRAKESee Fig HOW to USE Your TractorAttachment Clutch Switch Disengaged Engaged Stopping See FigTo Move Forward and Backward See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To USE Cruise Control J See FigTo Operate on Hills To Stop Mower BladesReverse Operation System ROS To Transport See FigCheck Engine OIL Level Service REMINDER/HOUR MeterBefore Starting the Engine ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP General Recommendations MaintenanceMaintenance ScheduleBlade Care BatteryTractor Blade Removal See FigEngine IN-LINE Fuel Filter See Fig CleaningDeck Washout Port See Fig To Install Mower See Figs Service and AdjustmentsTo Remove Mower See Fig Raise attachment lift lever to highest position To Level Mower To Replace Mower Blade Drive Belt To Check BrakeFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Replace Motion Drive Belt See Fig To Remove Wheel for Repairs See FigTransmission Fuel System StorageOther Engine OILTroubleshooting Problem Cause CorrectionFires when turn To run when operBattery will not Engine continuesSchematic SCH12Electrical KEY Part Description 196 Chassis 207 Drive Spark Arrester KIT EngineEngine Power Rating Information Steering Assembly 532 41 Wheel, Steering Seat Assembly 532 42 SeatDecals Wheels and TiresMower Deck Tractor Model NO. YTH2242TDF 96041017302, Product no 41 Mower Lift 532 40 34-07 Link Lift Susp Mower RearSuggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX12.01.10 CL/SR

YTH2242TDF specifications

The Husqvarna YTH2242TDF is a robust and reliable riding mower designed for homeowners seeking a machine that combines power, efficiency, and ease of use. Packed with essential features and advanced technologies, this mower stands out for its performance and versatility in tackling landscaping tasks.

One of the key features of the YTH2242TDF is its powerful 18.5 HP Briggs & Stratton engine. This durable engine ensures consistent performance, allowing users to navigate their lawns with ease. The Hydrostatic transmission further enhances this experience, providing a smooth and effortless driving experience without the need for manual gear changes. This user-friendly design enables operators of all skill levels to maneuver effectively and efficiently around their property.

The cutting deck of the YTH2242TDF measures 42 inches, making it suitable for medium to large sized lawns. This size allows for a wide cutting path, reducing the time needed to mow. The deck features a washing port, making maintenance a breeze by allowing users to easily clean the underside of the deck after mowing, helping to maintain optimal cutting efficiency.

Additionally, the mower is equipped with a compact design that provides excellent visibility and maneuverability in tight spaces. Its tight turning radius enables users to navigate landscaping features with precision, reducing the need for excessive trimming afterwards.

Another noteworthy attribute of the YTH2242TDF is its comfort features. The adjustable seat ensures that operators can find their ideal position, while ergonomic controls reduce fatigue during extended use. The easy-access controls are designed to enhance user comfort and efficiency, making the mowing experience more enjoyable.

For added versatility, the YTH2242TDF is compatible with a variety of attachments, including baggers, plows, and mulchers, making it an excellent investment for seasonal tasks beyond mowing. This flexibility allows users to maximize the utility of their mower throughout the year.

In terms of build quality, Husqvarna's commitment to durability is evident in the robust construction of the YTH2242TDF. The cutting deck is made from high-quality steel, ensuring it can withstand the rigors of regular use.

In summary, the Husqvarna YTH2242TDF is an exceptional choice for homeowners looking for a reliable, efficient, and easy-to-use riding mower. With its powerful engine, smooth transmission, and versatile design, it stands out as a valuable tool for maintaining beautiful lawns.
Top Page Image Contents