Behringer A50-13413-00005 manuals
Musical Instruments & Equipment > Microphone
When we buy new device such as Behringer A50-13413-00005 we often through away most of the documentation but the warranty.
Very often issues with Behringer A50-13413-00005 begin only after the warranty period ends and you may want to find how to repair it or just do some service work.
Even oftener it is hard to remember what does each function in Microphone Behringer A50-13413-00005 is responsible for and what options to choose for expected result.
Fortunately you can find all manuals for Microphone on our side using links below.
Behringer A50-13413-00005 Manual
24 pages 1.23 Mb
2 IMPORTANT SAFETY INSTRUCTIONS3 TABLE OF CONTENTS4 1. INTRODUCTION1.1 Before you get started5 Fig. 1.1: Swapping plugs on the switching power supply unit1.1.4 Initial operation of the microphone To change the transmitter (mic) batteries: Unscrew the bottom end of the microphone and pull out the battery compartment Remove the base plate in order to connect the battery to the contacts 6.Screw the bottom end of the microphone back on 1.1.5 Online registration 6 2.ULR2000 RECEIVER2.1Control elements and connections’s front side 7 COLOR CODEANTENNA Two bar antennae can be connected to the ANTENNA 1 and ANTENNA 2 connectors 2.1.2 Display Fig. 2.2: Closeup of the ULR2000 display display (antenna symbol) RF LEVEL Alphanumeric display CHANNEL UP and changes the transmission channel within the selected preset FREQ MHz If FREQ MHz lights up, changing the transmission channel using the also displays the frequency of the selected channel channel color ’s back 8 2.2 Menu items in detail9 A storage location can be selected by pressing the UP or DOWN buttonsor channel color) always 2.2.2 SCAN 1.Press the SET button to get to the menu Press the UP button once to get to SCAN ascending or descending direction. The scan begins UP or DOWN buttons now over, and the basic settings are shown in the display again 2.2.3 SQUELCH 0 dB: the receiver is not muted low dB value: high dB value: the receiver is muted even if the noise floor is low Setting a Squelch value 2. Press the UP button twice to get to SQELCH 0 and 40 dB can be selected in 5-dBincrements 10 2.2.4 AUTO MUTETo bridge this latency time, the ULR2000 offers a practical Auto Mute function: Activating/deactivating the Auto Mute function Press the UP or the DOWN buttons to turn the auto mute function on or off 2.2.5 DISPLAY DOWN buttons The exact channel carrier frequency is shown (FREQU) The channel number is shown in the display (CHANNL) The color assigned to the channel is shown in the display (COLOR) Changing the ULR2000’s basic settings Press the DOWN button three times to get to DISPL 2.2.6 LOCK Activating LOCK 2. Press the DOWN button twice to get to LOCK Press the SET button again to get to the LOCK submenu. The display shows LOCOFF LOC ON 11 Deactivating LOCK2.2.7 PRESET Factory presets (Presets 2, 3 and 4) User preset (Preset 1) Loading a preset 12 3. ULM2000 MICROPHONE3.1 Control elements 3.2 Hand-heldtransmitter operation13 Changing the channel when the transmitter is powered off3.2.3 Setting your own frequency 1.Engage MUTE. The transmitter can now be switched to the programming mode 3.Enter all 6 digits one after another in the following fashion: Confirm your selection by briefly pressing the POWER button 5.Confirm your selection by briefly pressing the POWER button 14 8.Disengage the MUTE switchA user-assignedfrequency is automaticallystored in the user preset (Preset 1) 3.2.4 Preset The ULM2000 lets you work with 4 presets, each with 8 channels Table 3.1: Factory preset frequencies (presets 2,3 and 4) 1.Engage MUTE. The transmitter can now be switched into the programming mode 4.Confirm your selection by briefly pressing the POWER button 15 7.After setting the desired preset, disengage the MUTE switch3.2.5 Mic Gain 3.Select one of the following two digits on the selection switch: Low Gain: select High Gain: select Low Gain: the LED blinks once with medium tempo High Gain: the LED blinks twice with medium tempo 7.Disengage MUTE 3.2.6 Auto Mute To bridge this latency time, the ULM2000 offers a practical Auto Mute function: 16 3.3 Status query17 3.5 ULM2000 level setting18 4. APPLICATION EXAMPLE5.INSTALLATION 21 6.SPECIFICATIONS23 FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATIONULTRALINK ULM2000/ULR2000Responsible party name: MUSIC Group Services USA, Inc Address: 18912 North Creek Parkway Suite 200 Bothell, WA 98011 USA Phone: +1 425 672 Fax: +1 425 673 Important information: 24 MICROPHONE QUICK START GUIDE
Also you can find more Behringer manuals or manuals for other Musical Instruments & Equipment.