Manuals
/
Brands
/
Computer Equipment
/
Switch
/
Bay Technical Associates
/
Computer Equipment
/
Switch
Bay Technical Associates
303, 304 manual
Please, tick the box below to download manual:
Contents
Main
ii
Federal Communications Commission (FCC) Statement
Statement of Conditions
Trademarks
Page
Page
Contents
Page
Page
Page
Figures
Page
Tables
Page
Preface
Audience
Purpose
Conventions
Use of Enter, Type, and Press
Two-tiered Procedure Format
Special Message Formats
Ordering Bay Networks Publications
How to Get Help
Bay Networks Customer Support
For More Information
Safety Alert Message Format
Page
Safety Alert Messages Used in This Guide
Class A Product
Accumulated Weight (Shelf or Table Mount)
Stacking Units in a Rack
Turning Off Power to the Unit
Reset To Default Settings Command
Removing the Top Cover
Chapter 1 Introduction to the BayStack 303 and 304 Ethernet Switches
Features
Page
Physical Description
Front Panel
Page
Page
Page
Introduction to the BayStack 303 and 304 Ethernet Switches
The console port connector pin assignments are described in Table 1-2.
Table 1-2. DB-9 connector pin assignments
Table 1-3. Front-panel LEDs
Power Cord Specications
Introduction to the BayStack 303 and 304 Ethernet Switches
Table 1-5 lists specications for international power cords.
Table 1-5. International power cord specications
Page
Chapter 2 Installing the BayStack Switches
Installation Requirements
Installation Procedure
Installing the BayStack Switches on a Flat Surface
Installing the BayStack Switch in a Rack
Page
Page
Page
Page
Attaching Devices to the BayStack Switch
Half-duplex and Full-duplex Mode
Autonegotiation
Page
Page
Power-up Self-Tests
Page
Initial Setup of a BayStack Ethernet Switch
Using Factory Default Settings
Selecting a Language
Installing the BayStack Switches
893-01010-A 2-17
Initial Switch Setup
Figure 2-9. Main Menu
2-18
To set the IP address, subnet mask, and gateway address for the switch, follow these steps:
1. Type 2 to select 2---System Conguration from the Main Menu.
This selection displays the System Conguration menu (see Figure 2-10).
Figure 2-10. System Conguration menu
Page
Page
Chapter 3 Customizing and Managing the BayStack Switches
Using the Menus and Screens
3-2
Figure 3-1. Menu and screen hierarchy
Customizing and Managing the BayStack Switches
893-01010-A 3-3
Menu and Screen Areas
Figure 3-2. Menu and screen areas
Page
Menu and Screen Descriptions
Language Selection Menu
Main Menu
System Information
Spanning Tree General Information
Page
Spanning Tree Port Information
Page
System Conguration
Page
Page
General Conguration
Port Conguration
Page
Reset System
Exit Telnet
Using the BayStack Switch
Conguration Examples
3-18
Figure 3-3. BayStack 304 switch as a segment switch
Spanning Tree Protocol
Managing the BayStack Switches
Page
Page
Upgrading Switch Software Through TFTP Connection
Page
Page
Page
Chapter 4 Troubleshooting and Diagnostics
BayStack 303 and 304 Switch-related Issues
Autonegotiation
Troubleshooting and Diagnostics
MDI and MDI-X Connections
Figure 4-1. MDI-X to MDI cable connections
Note: For the transmitter of one device to connect to the receiver of another
device, the sum of crossovers must always be an odd number.
4-4
Installation-related Issues
Addresses
Cabling
Link Status
Appendix A Technical Specications
General Specications
A-2
Declaration of Conformity
Page
Appendix B Media Dependent Adapters (MDAs)
100BASE-FX MDA
Page
10/100BASE-TX MDA
Installing an MDA
Page
Page
Index
Numbers
A
B
C
D
E
F
G
H
M
N
P
R
S
T
U
W