Manuals
/
Brands
/
Household Appliance
/
Furnace
/
Thermo Products
/
Household Appliance
/
Furnace
Thermo Products
OHFA199DV5B, OHFA199DV5R operation manual
Please, tick the box below to download manual:
Contents
Main
OIL FIRED FURNACE
INST ALLATION AND OPERATION M ANUAL WITH USERS INFO RM ATION SECTION
Page
Page
Page
Page
A. CODES AND CLEARANCES:
B. MAKE-UP AIR: Today's emphasis on home insulation increases the probability of inadequate air
II. GENERAL INSTRUCTIONS - READ BE F ORE ST ART OF INSTALLATION
WARNING:
A. CHIMNEY:
2. PROPER CHIMNEY HEIGHT:
3. PROPER VENT CONNECTOR PIPE/CHIMNEY CONNECTIO N:
5. TIGHT JOINTS:
6. TIGHT CLEAN-OUT DOORS AND CONNECTIONS:
7. NO INTERCONNECTED CHIMNEY FLUES:
8. FLUE PIPE CLEARANCES, SIZING AND TYPE:
REDUCTION OF CLEARANCES WI T H SPECIFIED FORMS OF PROTECTION:
B. VENTING:
CAUTION MUST BE TAKEN NOT TO EXCEED 90 ROTATION (OF THE FLUE ELBOW) .
ROTATION OF FRONT FLUE ELBOW:
C. DRAFT REGULATORS:
D. DUCT WORK/AIR CONDI TIONING:
Air flow Requirements and Sizing of Duct Work:
Page
Page
Page
E. Air Filter Mounted Ex ternal to Furnace:
Page
F. LIMIT POSITION AND LOCATION
TABLE 5: Installation location of the fan and limit control for each furnace
G. BURNER INS TALLATION:
H. BURNER SPECIFICATIONS AND APPLICATIONS:
Page
MOUNTING THE 2-STAGE RIELLO BURNE R:
I. OIL TANK AND PIPING:
J. OIL FILTER:
K. ELECTRICAL WIRIING:
Electronic Ai r Cl eaner (EAC) and Humidifier Installation:
Page
Preferred method of adjustment:
L. Blower Motor Speed S election:
28
Heating Speed Set-ups
Heating Speed Set-ups
OH8FA119DV5
Page
Page
32
NOTE: All information is approximate. Results will vary by installati o n .
33
34
OH8FA119D60
Speed vs. color code for PSC Motor: Low = Red Med-Low = Blue Med-High = Yellow High = Black
M. BLOWE R CONTROLLER INFORMATION FOR PSC MOTOR
Page
Page
Page
N. STARTUP PROCEDURES:
For You r Safety Read Before Operating:
Do not use this appliance if any part has been under water. Immediately call a qualified
Page
COMBUSTION HEAD SETTING F OR 2-STAGE RIELLO BURNER:
TURN TO THE RIGHT : (SIGN + )
TURN TO THE LEFT: (SIGN - ) Figure 21
AIR DAMPER ADJUSTMENT:
1st STAGE ADJUSTMENT:
2nd STAGE ADJUSTMENT:
NOTICE: Minimum temperature rise is 50F.; maximum temperature rise is 80F.
k.
l. Check for the presence of oil leaks. Correct any oil leaks found.
m. Reassemble the burner compartment cover.
3. Adjustm ent Of Heat Input Ra te:
NOTICE: It may be necessary to bleed air from the oil line before the burner can be fired.
4. Setting Supply Air Temperature Rise:
Page
Page
Page
IV. INS TALLER'S INSTRUCTIONS TO USER:
V. DEALER MAINTENANCE:
A. GENERAL INSPECTION:
WARNING: Shut off oil and disconnect power before continuing with this inspection.
B. HEAT EXCHANGER:
WARNING: A quali fied heating contractor must clean the heat exchanger.
C. HEAT EXCHANGER CLEANING INSTRUCTIO NS:
WARNING: THE HEAT EXCHANGER MUST BE CLEANED BY A QUALIFIED SERVICE PERSON.
Page
Page
Filter replacement:
G. EXTENDED APPLIANCE S HUTDOWN:
Page
Page
VII. TROUBLESHOOTING:
PERSONNEL, AND NOT BY THE FURNACE OWNE R.
A. DIAGNOSTICS :
Diagnostic Features:
B. CAD CELL CHECKOUT PROCEDURE:
Page
Page
Page
Page
Page
Page
Page
Page
manua l ca refully before m aking tes ts. Reta in this form with furna ce.