3D Connexion 466-1513-01 Using Programming Shortcuts

Concord 55

2. Press B until the touchpad displays “USER CODES,” then press #.

3. The touchpad displays “REGULAR USER CODES” or “REG CODES.” Press B until the

display reads “SYSTEM MASTER CODE” or “SYS MASTER,” then press #.

4. Replace the existing code with the new 4 digit System Master Code then press #.

5. Press * + 00 + #to exit the programming menus.

Using Programming Shortcuts

A programming shortcut is a number that “jumps” you to a particular spot in the programming

menus.

A series of shortcut numbers takes you directly to the feature or code you want to change.

1. Enter User Programming.

Local Phone # + 9 + CODE

Remote Phone Access Dial the phone number + # + CODE + # + 9 + CODE

Touchpad 9 + CODE

2. Enter a programming command sequence.

Time * + 020 + TTTT + #

Date * + 021 + DDMMYY + #

Regular User Codes User 00: * + 0300000 + NNNN + #

User 01: * + 0300010 + NNNN + #

User 02: * + 0300020 + NNNN + #

(Continues through User 229)

User 229: * + 0302290 + NNNN + #

If using alphanumeric or fixed display touchpads, use A and B to scroll

through the code attributes and change them as required.

Partition Master Codes Partition 1:* + 0310 + NNNN + #

Partition 2:* + 0311 + NNNN + #

System Master Code * + 0320 + NNNN + #

Direct Bypassing Attribute * + 030NNN1 + 1(off) or 2(on) + # (nnn = user no.)

Remote Access Attribute * + 030NNN2 + 1(off) or 2(on) + # (nnn = user no.)

Partition Jump Attribute * + 030NNN3 + 1(off) or 2(on) + # (nnn = user no.)

System Test Attribute * + 030NNN4 + 1(off) or 2(on) + # (nnn = user no.)

Latchkey Report Attribute * + 030NNN5 + 1(off) or 2(on) + # (nnn = user no.)

Downloading * + 040 + 1(off) or 2(on) + #

Silent Arming * + 041+ 1(off) or 2(on) + #

Touchpad Brightness * + 042 + 0 through 3 + #

Volume * + 043 + 0 through 7 + #

Voic e C him e * + 044 + 1(off) or 2(on) + #

Chime on Close * + 045 + 1(off) or 2(on) + #

Contents

Main g GE Security www.GE-Security.com C9 By p a s s Notices Commands at a Glance Contents Getting to Know Your Security System 1 Communicating with the Panel 2 Preventing Accidental Alarms 5 Basic System Operations 6 Panic Alarms 12 Access Codes 13 Setting the Time and Date 16 Adjusting System Sounds and Touchpad Brightness 17 Page Page Appendix A: User Sheets 41 g Appendix B: Planning for Emergencies 49 GE Security Appendix C: Programming Your System 53 Concord 1 Getting to Know Your Security Backup Module Environmental Detectors Motion Sensors Panel Communicating with the Panel Instructing the Panel TouchpadsYour System Interface Alphanumeric Touchpads Fixed Display Touchpads Wireless Handheld Touchpad Keychain Touchpads Notification by Pager What Happens in an Alarm Condition Fire and Smoke Alarms Resetting Smoke Detectors Preventing Accidental Alarms Aborting Accidental Alarms Guidelines for Preventing Accidental Alarms Basic System Operations Arming Your System Keychain Touchpad Arming Arming Level 1OFF Arming Level 2STAY Arming Level 3AWAY Quick Arm Using the Chime Feature Chime-On-Close Using the Voice Chime Feature Exit and Entry Delay Times Exit Delay Example Extended Delay Exit Extension No DelayFor Instant Alarm E x i t D e la y E n t r y D e l a y Auto STAY Arming Feature Arming While a Door or Window is Open Bypassing a Sensor Directly Bypassing a Sensor Indirectly Was the Bypass Successful? Basic Light Control Basic Output Control Checking the Status of Your System Short System Status Full System Status Panic Alarms Fire Panic Alarm Lighting During a Fire Panic Alarm Police Panic Alarm Lighting During a Police Panic Alarm Access Codes Programming Access Codes Changing or Erasing User Codes Assigning Code Attributes Setting the Time and Date Adjusting System Sounds and Touchpad Brightness Arming Your System Silently Adjusting the Touchpad Beeps (Fixed Display Touchpad Only) Adjusting the System Status Voice Volume Adjusting the Touchpad Display Brightness Using the Energy Saver Feature Energy Saver Example Setting the Energy Saver High and Low Temperature Settings Notification by Pager Pager Messages Event Code in Page Creating Time Schedules One Day Rollover Multiple Day Rollover Attaching Time Schedules Time Schedules and Partitions Advanced Light Control Controlling Lights By Time Schedule 9 + System or Partition Master CODE Controlling Lights with Sensors Installer Programmable Lighting Controlling Outputs by Time Schedule Scheduled Arming Opening and Closing Reports When Will this Feature Be Active? Latchkey Paging Page In the Event of... Who Will Be Paged? Latchkey Opening Basic Latchkey Opening Advanced Latchkey Opening Latchkey Closing Assigning a Time Schedule to Latchkey Paging Notify by Exception Page In the Event of... Who Can Send a Page? When Will this Feature Be Active? Assigning a Time Schedule to Exception Opening and Closing The No Activity Feature Using the Panel Download Feature Using a Partitioned Global Settings Partition-Specific Settings Jumping Partitions Arming and Disarming the Other Partition System Information Viewing Event Buffer Overview Page User information is shown in the following table. Using a Touchtone Phone to Operate Your Phone Command Prefix Accessing the System from Off-site How the Panel Answers the Phone Codes with Remote Access Capability Touchtone Phone System Operation Sending a Police Panic Alarm Phone Questions? Testing the System Automatic Test Features Manual Tests Sensor Test Phone Communication Test Testing Sirens Troubleshooting Trouble Beeps and Trouble Messages Silencing Trouble Beeps Common Questions and Answers Phone Issues Siren Issues Lighting Issues Page Appendix A: User Sheets should be completed by the installer and the user. System Sensors User Codes The table below provides a space for you to record user code information. Touchpad Information Alphanumeric and Fixed Display Touchpads Keychain Touchpads Keychain Touchpad 3 Active for Partition: 1 2 Latchkey User: Y N Keychain Touchpad 4 Accidental Smoke and Fire Alarms Dialer Abort Doors and Delay Time Settings System Features If the Power Goes Out No Activity Time Resetting the Smoke Detector System Information Paging Lights Outputs Energy Saver Alarm Sounds and Status Beeps Appendix B: Planning for Emergencies Floor Plan Example Figure 15. Floor Plan Example Your Floor Plan Page Alarm System Limitations If Your System Needs Service Appendix C: Programming Your System Two Methods to Program Your System * Using Programming Menus Examples of Programming Using Menus Page Using Programming Shortcuts Page Page Page Concord 59 + S y s te m M a s t e r o r P a r t it io n M a s te r C o d e T o e n t e r t h e P ro g ra m m i n g M e n u , p re s s * * * * ** d e f a u lt s . 1 . U n d e rl in e d s e tt in g s i n d ic a t e N o t e s ** N o t e s d e f a u lt s . 1 . U n d e rl i ne d s e tt in g s in d i ca t e