Manuals / 3M / Household Appliance / Pet Fence

3M 39600 manual Adjustments Continued

Models: 39600

1 94

Download 94 pages 44.17 Kb

Page 35

Adjustments (Continued)

Adjustments (Continued)

WARNING – Turn air and electrical supplies off and disconnect before beginning adjustments. Failure to comply with this warning could result in severe personal injury or equipment

damage.

Upper Taping Head Leveling

If the upper taping head is not horizontal, it can be leveled by adjusting the self-locking nut.

1.Loosen the five bolts on each side of crossbar shown in Figure 5-2A.

2.Remove access cover as shown in Figure 5-2B and (using M13 hex key wrench) tighten or loosen M8 self-locking nut until upper head is level.

3.Take measurement from exit end of upper head assembly and front of flap folding ski to machine bed, as shown in Figure 5-2. Upper assembly must be level ±1.5 mm [±1/16 inch].

4.Retighten five bolts on each side of crossbar to secure adjustment.

Figure 5-2 – Upper Taping Head Leveling

30

Image 35

3M 39600 manual Adjustments Continued

Contents

3M-Matic AdjustableInstructions and Parts List Important Safety Information241 Venture Drive Replacement Parts and Service InformationTo Our Customers 3M/Tape Dispenser PartsAVAILABLE DIRECT FROM Replacement Parts And Service InformationSERVICE, REPLACEMENT PARTS AND ADDITIONAL MANUALS To Our CustomersPage Table of ContentInstruction Manual Section II - AccuGlide STD 3 Inch Taping Heads Table of Content ContinuedPage Intended Use Contents - 800af3 Adjustable Case Sealer Important Safeguards Important Safeguards Continued Figure 1-8 - Safety Instructions Label Figure 1-12 - Lifting Notice Label 2. Operating Rate Specifications1. Power Requirements 5. Tape Width Specifications Continued3. Operating Conditions 4. TapeMUST BE GREATER THAN 9. Box Weight and Size CapacitiesDETERMINE THE BOX LIMITATIONS BY COMPLETING THIS FORMULA BOX LENGTH IN DIRECTION OF SEAL10. Machine Dimensions CAUTION - Machine weighs approximately 370 kg 820 lbs uncrated Installation and Set-UpReceiving And Handling Machine Set-UpFigure 2-2 - Lower Tape Drum Bracket Position Installation and Set-Up ContinuedFigure 2-1 - Installation and Set-Up Figure 2-3 - Conveyor Systems Figure 2-4 - Conveyor Bed Height AdjustmentFigure 2-3 - Pneumatic Connection WARNING - USE CARE WHEN WORKING WITH COMPRESSED AIRInitial Start-Up of Case Sealer Figure 3-1 - Case Sealer Components Operation2 Main Air On/Off Valve/Pressure Regulator/Filter -Figure Figure 3-2 - Controls, Valves and Switches 1 Electrical On/Off SwitchOperation Continued 7 Indicator, Air Pressure Figure 3-3 - On/Off Valve/Regulator/Filter 3 Emergency Stop Switch4 Height Adjustment Crank, Upper Taping Head 5 Width Adjustment CrankWARNINGS Figure 3-6 - Box Size Set-Up Figure 3-5 - Tape Threading With Alternate Outboard Tape DrumBox Size Set-Up Move the compression rolls as wide as possibleFigure 3-7 - Box Size Set-Up Figure 3-8 - Box Size Set-Up WARNING - Be sure all packaging materials and tools are removed from Figure 3-12 - Box Size Set-Up WARNING - Keep hands away from drive belts and flap kicker whenfeeding boxes to the machine Figure 3-11 - Box Size Set-Upoccur WARNINGS2. Turn off machine Lubrication MaintenanceCleaning WARNING - Turn air and electrical supplies off and disconnect beforeFigure 4-2 - Drive Belt Replacement Maintenance Continueddamage Drive Belt Replacement/Tension Adjustment Figure 4-4 - Drive Belt Tension Adjustment Top View Figure 4-3 - Drive Belt Replacement/Tension Adjustmentequipment damage Air Line Filter -Figure Drive Belt Tension AdjustmentsTaping Head Adjustments -Refer to Section Gate OperationAdjustments Continued The gate air pressure is controlled by a regulator mounted under the machine frame. This provides adjustment of the gate lifting force. When light weight boxes are being run the gate pressure can be reduced to minimize lifting of the box THIS PAGE IS BLANK Special Set-Up Procedure Figure 6-3 - Removing Taping Heads from Case Sealer Special Set-Up Procedure ContinuedChanging the Tape Leg Length from 70 to 50 mm 2-3/4 to 2 inches TAPING HEADSOuter Column Re-Positioning Refer to Figure Figure 6-4 - Column Re-Positioning Special Set-Up Procedure ContinuedCause TroubleshootingTroubleshooting Guide ProblemTroubleshooting Continued Pneumatic Diagram Electrical Diagram Page THIS PAGE IS BLANK Spare and Miscellaneous Parts Options/Accessories Frame Assemblies Replacement Parts - Illustrations and Parts Lists800af3 Adjustable Case Sealer, Type 39600 3 Inch Width Taping Heads THIS PAGE IS BLANK 800af3 Adjustable Case Sealer Frame Assemblies 800af3 Adjustable Case Sealer Description Ref. No3M Part No 800af3 Adjustable Case Sealer Description Ref. No3M Part No 800af3 Adjustable Case Sealer Description Ref. No3M Part No 800af3 Adjustable Case Sealer Description Ref. No3M Part No 800af3 Adjustable Case Sealer Description Ref. No3M Part No 800af3 Adjustable Case Sealer Figure 3027/1 of Figure 3027 Page 1 of 800af3 Adjustable Case Sealer Figure 3027/2 of Description Figure 3027 Page 2 ofRef. No 3M Part No800af3 Adjustable Case Sealer 3183-2 Ref. No3M Part No Description800af3 Adjustable Case Sealer 3184-2 Ref. No3M Part No Description800af3 Adjustable Case Sealer Figure 4184/1 of Description Figure 4184 Page 1 ofRef. No 3M Part No800af3 Adjustable Case Sealer Figure 4184/2 of Description Figure 4184 Page 2 ofRef. No 3M Part No800af3 Adjustable Case Sealer Figure 4184/3 of Description Figure 4184 Page 3 ofRef. No 3M Part No800af3 Adjustable Case Sealer Figure 4184/4 of Description Figure 4184 Page 4 ofRef. No 3M Part No800af3 Adjustable Case Sealer Description Ref. No3M Part No 800af3 Adjustable Case Sealer Figure 4186/1of Description Figure 4186 Page 1 ofRef. No 3M Part No800af3 Adjustable Case Sealer Figure 4186/2 of Description Figure 4186 Page 2 ofRef. No 3M Part No800af3 Adjustable Case Sealer Figure 4188/1 of Description Figure 4188 Page 1 ofRef. No 3M Part No800af3 Adjustable Case Sealer Figure 4188/2 of Description Figure 4188 Page 2 ofRef. No 3M Part No800af3 Adjustable Case Sealer Description Ref. No3M Part No 800af3 Adjustable Case Sealer Description Ref. No3M Part No 800af3 Adjustable Case Sealer Safety and Information Labels Description Safety and Information LabelsRef. No 3M Part No