GB
802CC | 852CC |
Schleicher International
OPERATING FUNCTIONS (Figs. 1, 2 and 4):
1 = Mains switch
2 = „Cutting system forward“ pushbutton (fig. 2)
Pressing this button starts the cutting system. Material can now be fed to the shredder.
3 = „Cutting system stop“ pushbutton (fig. 2)
Pressing this button switches the shredder off, thereby halting the cutting system.
4 = „Cutting system reverse“ pushbutton (fig. 2)
Pressing this button starts the cutting system in reverse.
5 = Pilot lamp (fig. 2)
a)„ready“
Continously lights when the mains switch
(1)is operated.
b)„motor protection“
Flashes when the motor is overloaded. While the motor is cooling down, the machine cannot be switched on to „forward“
run.
6 = Pilot lamp „paper jam“ (fig. 2)
Lights when too much paper is fed to the cutters (see description „AUTOMATIC RESPONSE IN CASE OF OVER- LOADING“).
7 = Pilot lamp (fig. 2)
a)„door open“/„hopper open“
Lights when the door is not closed or when the hopper is open. The machine then switches off automatically and it cannot be started as long as the door is open or the hopper is open.
b)„collecting bag full“ (fig. 2)
Lights as soon as the collecting bag is full and needs to be emptied. At the same time the machine switches off automatically.
8 = Light barrier (forward operation) (fig. 4) The shredding operation is started as soon as a sheet of paper passes through the feed slot.
OPERATION
OPERATING THE MACHINE:
To start, switch on the unit by operating the mains switch (1) (fig. 1). The pilot lamp marked „ready for operation“ (5), as well as the red
(3)(fig. 2) will light to indicate that the machine is ready for operation.
The paper tray may not be used as a step ladder or as a seat. Danger of tipping over!
FEEDING CRUMPLED PAPER (MODEL 852CC):
In order to avoid a reduction of user safety by increasing the height of the hopper side panels, and in order to allow for filling the hopper while standing on the floor, the height of the hopper side panels is not in compliance
with EN 294:1992.
The deviation from EN 294:1992 is identified with a
1.Fill the hopper with crumpled paper.
Note: The crumpled paper can be dropped directly from the wastepaper basket into the hopper of the machine. The apportioning wings preceding the cutting mechanism ensure more or less uniform distribution of the paper.
Attention: The wastepaper basket is no refuse tin and should not be emptied into the machine thoughtlessly - in no way can the machine destroy bottles, pens, pencil sharpeners etc.
2.Press the pushbutton switch „forward“ (2) (fig. 2). The cutting system runs and begins to shred the paper.
Note: Do not feed any smooth paper until the crumpled paper is completely shredded.
3.To switch the machine off press the red stop- button (3) (fig. 2).
FEEDING SMOOTH PAPER:
-Feed smooth paper through the opening at the lower part of the hopper (model 852CC) or through the opening of the hopper (model 802CC) to the cutting system.
-Machine switches automatically to forward and draws paper in.
-The machine switches off automatically after shredding.
Never feed the shredder with a quantity of paper exceeding the maximum indicated in the technical details.
Should the machine be overfed, follow the instructions under „AUTOMATIC RESPONSE IN CASE OF OVERLOADING“.
AUTOMATIC RESPONSE
IN CASE OF „OVERLOADING“:
In case you accidentally overload the shredder, it will automatically alleviate the problem as follows:
1.The cutting system becomes jammed. The pilot lamp (6) (fig. 2) lights up.
2.The cutting system runs briefly in reverse, thereby freeing the material to be shredded.
3.The cutting system automatically switches back to forward mode.
The machine repeats this process until all the material has been shredded satisfactorily.
EMPTYING THE COLLECTING BAG (Fig. 3): When the collecting bag is full, the machine turns off automatically. The pilot lamp (7) (fig. 2) lights up. Empty the collecting bag as follows:
-Open the door and take out the sliding frame with the collecting bag.
-Remove the rubber band, take out the full bag and dispose of contents.
-Put the empty bag from below through the sliding frame and put the edges of the bag approx. 10 cm over the frame outwardly.
-Fix the collecting bag with the rubber band at the sliding frame.
-Move back the sliding frame with the collecting bag and close door.
Note: The machine will only run with closed door!
I
MAINS SWITCH
1
fig. 1
S
4 3 2 5 6 7
fig. 2 | fig. 3 |
6 | |
|
