Troubleshooting
Problem | Possible Cause | Correction |
Odor in cabinet | • Unit interior needs cleaned. |
• Clean inside of unit. See “Care and Cleaning” pg. 7.
|
|
|
|
|
|
|
|
| Noisy operation |
| • | Unit not level. | • Adjust leveling legs. See leveling leg instructions. |
| |
|
|
| |||||
|
|
|
|
|
|
| |
| Unit vibrates |
| • | Unit not level. | • Adjust leveling legs. See leveling leg instructions. |
| |
|
|
|
|
|
|
| |
|
|
| • | Weak floor. | • Rebuild floor or move to a different location. |
| |
|
|
|
|
|
|
|
|
| Interior light not working |
| • | LED light burned out. | • | Replace LED light. |
|
|
|
|
|
|
| ||
|
|
| • No power at outlet. | • Test outlet with lamp. |
| ||
|
|
|
|
|
|
| |
| Appliance will not run. |
| • | Control Panel turned “OFF”. | • Turn unit on with on/off pad on Control Panel. |
| |
|
|
|
|
|
| ||
|
|
| • Line Cord not plugged into power source. | • Plug unit into power source. |
| ||
|
|
|
|
|
|
|
|
|
|
| • | House fuse blown. | • | Reset house fuse. |
|
| Appliance runs too long. |
| • | Prolonged door openings. | • Reduce number and/or duration of door openings. |
| |
|
|
| • Control Panel set too cold. | • Raise temperature of unit via Control Panel. |
| ||
|
|
|
|
|
|
| |
|
|
| • | Condenser needs cleaning. | • Clean condenser. See “Care of Unit” pg 7. |
| |
| Moisture collects inside of unit. |
| • | Too many door openings. | • Reduce number and/or duration of door openings. |
| |
|
|
|
|
|
|
| |
|
|
| • | Prolonged door openings. | • Reduce number and/or duration of door openings. |
| |
|
|
|
|
|
| ||
|
|
| • Hot, humid weather increases | • As humidity decreases, moisture will disappear. |
| ||
|
|
|
| condensation. | • Move unit to cooler location. |
| |
|
|
|
|
|
|
| |
| Moisture collects on outside surface |
| • | Hot, humid weather increases | • As humidity decreases, moisture will disappear. |
| |
| of the unit. |
|
| condensation. | • Move unit to cooler location. |
| |
|
|
| • | Control improperly set. | • Reset to slightly warmer temperature. |
| |
| Interior too hot/too cold |
| • | Control improperly set. | • Reset control to desired temperature. |
| |
|
|
| • | Faulty thermometer. | • Recheck with second thermometer. |
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Diagnostic LED
In the back in the grille there is a diagnostic/status LED. This led is used to help diagnosis any problems with the unit and to tell its status.
LED Status | Code/Problem |
Not on | Unit does not have power |
Continuously on | Unit is "ON" and operating correctly |
1 Blink and pause | For shorted or open thermistor |
2 Blink and pause | Disconnected Display Board |
|
|
3 Blink and pause | Compressor is locked out |
|
|
All specifications and product design subject to change without notice. | 7 |
Such revisions do not entitle the buyer to corresponding changes, improvements, additions, replacements or compensation for previously purchased products.