Agilent Technologies EN 60555, EN 61000-3-2, EN 61000-3-3 A

73

A

Specifications

Supported or Referenced EN 61000-3-2 and EN 60555 Part 2 Standards

IEC 555-2 EN 61000-3-2

EN 60555 Part 2 IEC 1000-3-2

IEC 1000-4-7

Supported or Referenced EN 61000-3-3 Standards

IEC 725 EN 61000-3-3

IEC 868 IEC 1000-3-3

IEC 868 Amendment 1

PC Requirements

Minimum: 486DX 33 Mhz

512 Kbytes of conventional memory

8 Mbytes of RAM

210 Mbyte IDE Hard Disk1 (4 Mbytes required for installation)

Windows 3.1, or Windows for Workgroups 3.11

Networking disabled

Recommended: 486DX4 100 Mhz or Pentium

512 Kbytes of conventional memory

16 Mbytes of RAM

1.2 Gbyte IDE PCI Hard Disk1 (4 Mbytes required for installation)

Windows 95 workstation2, or Windows NT 4.0 workstation

Networking disabled

1Accommodates data storage for the maximum possible test length of 7 days.

2For Windows 95, plug and play I/O cards are recommended.

Supported GPIB Interfaces

Agilent 82335B, 82340B, 82341C/D, 82350A GPIB Interface

National Instruments AT-GPIB/TNT, AT-GPIB/TNT PnP (Windows 95 only), AT-GPIB/TNT PCMCIA

Supported Equipment

Agilent 6812B AC Power Source/Analyzer (300 V, 6.5 Arms max., single-phase)

Agilent 6813B AC Power Source/Analyzer (300 V, 13 Arms max., single-phase)

Agilent 6841A Harmonic/Flicker Test System (300 V, 6.5 Arms max., single-phase)

Agilent 6842A Harmonic/Flicker Test System (300 V, 13 Arms max., single-phase)

Agilent 6843A Harmonic/Flicker Test System (300 V, 16 Arms max., single-phase)

Contents

Main Users Guide Notice Warranty Limitation of Warranty Revisions Printing History Table of Contents 1 INTRODUCTION 7 2 INSTALLATION 11 3 SETTING UP THE TEST 17 4 RUNNING THE TEST 27 5 VIEWING TEST DATA 37 6 SEARCHING FOR SPECIFIC TEST DATA 65 B GLOSSARY 77 7 PRINTING 69 A SPECIFICATIONS 73 C IEC MODE COMMAND SUMMARY 81 D CLASS DETERMINATION 95 INDEX 101 Page Introduction How to Use this Manual The Agilent 6800-Series AC Power Source/Analyzers The Agilent 14761A Harmonic/Flicker Test System Software EN 61000-3-2 and EN 60555 Part 2 Regulations Compliance Testing Implementation EN 61000-3-3 Regulation Compliance Testing Implementation Installation Install the Software Connect the Equipment Installing Interface Card Drivers for Windows 3.1 or 3.11 Systems Installing Interface Card Drivers for Windows 95 Systems Verify the Configuration Page Default Settings Getting Around in the Application Drop-down Menu Page Menu Tabs Setting Up the Test Select a Test Type Page Create a Template Select the Test Setup Options for Quasi-stationary or Fluctuating Harmonics Standard Test Options Advanced Test Options Page Test Termination Options Select the Test Options for Voltage Fluctuations Standard Test Options Advanced Test Options Test Termination Options Running the Test To Run a Pre-test for Quasi-stationary or Fluctuating Harmonics Pre-Test Summary Page Pre-Test Power Statistics Pre-Test Source Harmonics To Run a Pre-test for Voltage Fluctuations Pre-Test Summary Pre-test Measurements () = = THD n Max harmonic V To Run a Test Page Test Status Information Validation Mode Viewing Test Data Navigator Toolbar Viewing Quasi-stationary and Fluctuating Harmonics Graph Display Page Page Table Display Time-Series Display Page Page Statistics Display Probability Display (for Quasi-stationary or Fluctuating harmonics) Viewing 2.5 Minute Window Failures Page Viewing Voltage Fluctuations Pst Display Probability Display (for Voltage Fluctuations and Flicker) Page Distribution Display RMS Display Flicker Display Page Editing the Graph Attributes To change the attributes or the settings of any of the graphs, Copying Graphs and Tables to the Clipboard Using the Print Screen keyboard key Using the Copy Commands Viewing Reports Causes for Non-compliant EN 61000-3-2 or EN 60555-2 Tests Causes for Non-compliant EN 61000-3-3 Tests Short Form Report 5 - Viewing Test Data Long Form Report of a Fluctuating Current Harmonics test: Long-Form Report page #1 Long-Form Report page #2 5 - Viewing Test Data Long-Form Report page #4 Remarks Report Page Searching for Specific Test Data Searching for Data While the Test is Running Searching for Data After the Test has Completed Using the Span Control Using the Zoom Control Obtaining Detailed Failure and Error Information Printing Printing Graphs and Tables Using the Print Pre-test command Using the Print Graph/Table command Printing Reports Printing Reports to a File Page Page A Specifications Supported or Referenced EN 61000-3-2 and EN 60555 Part 2 Standards Supported or Referenced EN 61000-3-3 Standards PC Requirements Equipment Specifications (IEC Mode) IEC mode specifications are warranted over the ambient temperature range of 0 to 40 C. Specifications - A Ac Input Ratings and supplemental information IEC Mode Measurement System Characteristics for Agilent 6841A, 6842A, 6843A Page B Glossary Page Page Page C IEC Mode Command Summary Introduction Using the SENSe:CURRent:ACDC:RANGe command Command Syntax :LIMit : CALCulate:INTegral:TIME CALCulate:SMOothing CALCulate:LIMit:UPPer FORMat FORMat:BORDer MEASure:ARRay:CURRent:HARMonic? MEASure:ARRay:VOLTage:FLUCtuations:ALL? Command Summary - C repeat 60 times CALC:INT:TIME times <n> repeat <n> times MEASure:ARRay:VOLTage:FLUCtuations:FLICker? MEASure:ARRay:VOLTage:FLUCtuations:PST? SENSe:CURRent:PREFerence SENSe:WINDow SYSTem:CONFigure Page D Class Determination Page Page Page Page Page Index 2 A C D G H I L M Q R S T U W Z Agilent Sales and Support Offices