Manuals / Brands / Computer Equipment / Computer Accessories / Albatron Technology / Computer Equipment / Computer Accessories

Albatron Technology KI51PV-754 Mainboard KI51PV-754, Rebuilding a RAID Mirrored Array

1 58

Download 58 pages, 7.74 Mb

Mainboard KI51PV-754

After the array is successfully deleted, the screen will display as shown below.

Rebuilding a RAID Mirrored Array

This section applies to Mirrored, Striped Mirroring RAID and RAID 5 configurations and describes how to reestablish the integrity of a mirrored environment after replacing one of the drives (typically because of a single disk failure). After replacing the errant drive, the rebuild process will move data from its mirrored sibling drive (the drive with information still intact) to the newly installed drive. This only applies to mirrored configurations (RAID 1, RAID 0+1, RAID 5).

Contents

Copyright Trademark Disclaimer FCC Compliance Statement CE Mark nVIDIA® nForce4 C51PV & MCP51 Supports Socket AMD® AthlonTM 64/ SempronTM Processor Dimensions (Micro-ATX Form-Factor): Things You Should Know Packing List Symbols Table of Contents Introduction Specification CPU: Chipset: Memory: Slots: IDE Connector: Serial ATA II Connector: Onboard I/O facilities: Onboard USB Ports: Onboard AC’ 97 Audio CODEC: BIOS: Green Function: Shadow RAM: Flash Memory: Hardware Monitor Function: Configuration Layout of KI51PV-754(Right Side) Layout of KI51PV-754(Back Side) Hardware Installation CPU Processor Installation CPU Socket 754 Configuration Steps: FAN Headers: CPUFAN, CHASFAN Memory Installation: DIMM1 Memory Setup Steps: Back Panel Configuration PS/2 Mouse & PS/2 Keyboard Ports: KB/MS DVI & VGA Connectors: DVI, VGA USB & LAN Ports: USB1, USB2, USB/LAN Audio Ports: Sound Connectors Floppy Disk Drive Connector: FDC Hard disk drive Connectors: IDE1/IDE2 SATA II Connector: SATA1/SATA2/SATA3/SATA4 Front Panel Headers: SW/LED, SPEAKER Headers & Jumpers Front USB Header: USB1/2 TV OUT Header: TV_OUT IrDA Header: IrDA Serial Interface Header: COM1/COM2 Printer Interface Header: PRT USB Power Selection Header: JP2 Clear CMOS Jumper: JP1 Audio Configuration SPDIF Header: SPDIF (Optional) Front Audio Connector: FRONT AUDIO Slots PCI Slot: PCI1 Power Supply Attachments ATX Power Connector: ATX_PWR, ATX_12V Introduction Key Function Main Menu Item Options Description Advanced BIOS Features Removable Device Priority Hard Disk Boot Priority First /Second/Third Boot Device Boot Other Device Virus Warning CPU Internal Cache External Cache Quick Power On Self Test Swap Floppy Drive Advanced Chipset Features PnP/PCI Configurations Frequency/Voltage Control CPU Speed Detected CPU Host Frequency (MHz) CPU Spread Spectrum DDR Speed (strobe/sec) Hammer Fid control Integrated Peripherals Init Display First IDE Function Setup Onboard Device Onboard I/O Chip Setup Hot Key Power ON Onboard FDC Controller Onboard Serial Port Onboard Parallel Port Parallel Port Mode Power Management ACPI Suspend Type Power Management Video Off Method HDD Power Down HDD Down In Suspend Soft-Offby PWRBTN PCI PME Wake Up Hardware Monitor Load Defaults Load System Default Settings Load System Turbo Settings Load CMOS From BIOS Exit Menu Save & Exit Setup Exit Without Saving Software List Software Installation Page Page Page Page Appendix I: Super 5.1 Channel Audio Effect Setup Channels Setup Super 5.1 Channel Audio Effect Speaker Test Appendix II: RAID Setup Introduction to RAID Before create RAID Array NVIDIA RAID Utility Configuration Creating New RAID Array Page Deleting an Array Rebuilding a RAID Mirrored Array Before you rebuild a RAID Mirrored Array Install the OS of Windows® 2000/XP into your RAID HDDs Appendix III: ABS (Albatron BIOS Security) Card Setup Introduction Preparation and Setup Onoboard BIOS Recovery Procedures Type “dir” Note the file name of .bin Type “awdflash(space) xxxx.bin” Type N Type Y When the flash process is complete, press ‘F1’