Operating Instructions
DMP OPL Features
DIP Switch SettingsThe DMP has an 8 position DIP switch bank that is accessible from the back of the control board. By switching these DIP switches, it is possible for the operator to customize the display and some of the operating features of the tumbler.
Dip Switch |
|
| Funtion |
|
| |
|
|
|
|
|
| |
1 | Tumbler Type | ON - Coin |
|
| ||
OFF - OPL |
|
| ||||
|
|
|
| |||
|
|
|
|
|
| |
2 | Temperature Units | ON | - C |
|
| |
OFF* - F |
|
| ||||
|
|
|
| |||
|
|
|
| |||
3 | Local or Remote Reversing | ON* - Local Reversing |
| |||
OFF | - Remote Reversing |
| ||||
|
|
| ||||
|
|
|
|
| ||
4 | Empty | ON* |
|
| ||
|
|
|
|
| ||
5 | Empty | ON* |
|
| ||
|
|
|
| |||
6 | Buzzer Timer | ON - Continuous |
| |||
OFF - 5 Sec |
|
| ||||
|
|
|
| |||
|
|
|
|
| ||
|
|
| Dip Switch |
| ||
|
|
|
|
|
|
|
| OPL Models - Safety Tumble |
| #1 |
| #7 |
|
| OFF |
| ON | Safety Tumble | ||
|
|
| ||||
|
|
|
|
|
| |
7 |
| OFF |
| OFF | No Safety Tumble | |
|
|
|
|
|
| |
|
| Dip Switch |
| |||
|
|
|
| |||
|
|
|
|
|
|
|
| Coin Models - Coin Count/Pay |
| #1 |
| #7 |
|
| ON |
| ON | Coin Count | ||
|
|
| ||||
|
|
|
|
|
| |
|
| ON |
| OFF | Pay | |
|
|
|
|
|
|
|
8 | Programming | ON | - Enable |
|
| |
OFF* - Disable |
|
| ||||
|
|
|
| |||
|
|
|
|
|
|
|
* Factory default setting |
|
|
|
|
| |
|
| Table 2 |
|
| ||
1.Tumbler Type: This DIP switch selects the type of tumbler, i.e., OPL or Coin.
2.Temperature Units: Selects ºF or ºC for the temperature display. Factory setting is for ºF.
3.Local/Remote Reversing: Preset at the factory; usually for local reversing. Remote reversing for use with Reversing Timer Board only.
4.Empty: Preset at the factory; always ON.
5.Empty: Preset at the factory; always ON.
6.Buzzer Timer: This DIP switch determines the length of time that the end of cycle buzzer will remain on. “OFF” indicates that the buzzer will sound for 5 seconds when the drying cycle is completed. “ON” indicates that the buzzer will sound continuously until the STOP button is pressed or the loading door is opened.
7.Safety Tumble (OPL) or Coin count/Pay (Coin): If DIP switch #1 is set for OPL, then DIP switch #7 in the ON position enables the safety tumble. If DIP switch #1 is set for Coin, then DIP switch #7 in the ON position enables the display of the coin count. DIP switch #7 in the OFF position enables the display of “PAy,” to indicate that coins are needed to run the tumbler.
8.Programming: This switch enables or disables the programming feature and should normally be in the OFF position.
70400001 | © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT | 17 |