Step 5: (Gas Dryer Only) Connect Gas Supply Pipe

WARNING

To reduce the risk of gas leaks, fire or explosion:

The dryer must be connected to the type of gas as shown on nameplate located in the door recess.

Use a new flexible stainless steel connector.

Use pipe joint compound insoluble in L.P. (Liquefied Petroleum) Gas, or Teflon tape, on all pipe threads.

Purge air and sediment from gas supply line before connecting it to the dryer. Before tightening the connection, purge remaining air from gas line to dryer until odor of gas is detected. This step is required to prevent gas valve contamination.

Do not use an open flame to check for gas leaks. Use a non-corrosive leak detection fluid.

Any disassembly requiring the use of tools must be performed by a suitably qualified service person.

W316

1.Make certain your dryer is equipped for use with the type of gas in your laundry room. Dryer is equipped at the factory for Natural Gas with a 3/8 inch NPT gas connection.

NOTE: The gas service to a gas dryer must conform with the local codes and ordinances, or in the absence of local codes and ordinances, with the latest edition of the National Fuel Gas Code ANSI Z223.1/NFPA 54 or the CAN/CSA-B149.1 Natural Gas and Propane Installation Code.

Natural Gas, 1000 Btu/ft3 (37.3 MJ/m3) service must be supplied at minimum 5.0 inch water column pressure to maximum 10.5 inch water column pressure.

For proper operation at altitudes above 3000 feet

(915 m) the natural gas valve spud orifice size must be reduced to ensure complete combustion. Refer to Table 1.

Natural Gas Altitude Adjustments

Altitude

 

Orifice Size

 

Part No.

 

 

 

 

 

 

 

feet

m

No.

 

inches

 

mm

 

 

 

 

 

 

 

 

 

 

 

3000

915

43

 

0.0890

 

2.26

503778

 

 

 

 

 

 

 

 

6000

1830

44

 

0.0860

 

2.18

58719

 

 

 

 

 

 

 

 

8000

2440

45

 

0.0820

 

2.08

503779

 

 

 

 

 

 

 

 

9000

2740

46

 

0.0810

 

2.06

503780

 

 

 

 

 

 

 

 

10,000

3050

47

 

0.0785

 

1.99

503781

 

 

 

 

 

 

 

 

Table 1

2.Remove the shipping cap from the gas connection at the rear of the dryer. Make sure you do not damage the pipe threads when removing the cap.

3.Connect to gas supply pipe.

NOTE: When connecting to a gas line, an equipment shut-off valve must be installed within

6 feet (1.8 m) of the dryer. An 1/8 in. NPT pipe plug must be installed as shown for checking inlet pressure. Refer to Figure 11.

1

5

2

3

4

D434I

1New stainless steel flexible connector - (Use design CSA certified connector) Use only if allowed by local codes

21/8 in. NPT Pipe Plug

3Equipment Shut-Off Valve

4Black Iron Pipe

Shorter than 20 ft. (6.1 m) - Use 3/8 in. (9.5 mm) pipe Longer than 20 ft. (6.1 m) - Use 1/2 in. (12.7 mm) pipe

53/8 in. NPT Gas Connection

Figure 11

10

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

802715

Page 10
Image 10
Alliance Laundry Systems Dishwasher manual Gas Dryer Only Connect Gas Supply Pipe

Dishwasher specifications

Alliance Laundry Systems is renowned for its commitment to quality and innovation in the field of commercial laundry and cleaning solutions. Among its impressive lineup, the Alliance Dishwasher stands out as a robust solution designed for heavy-duty performance, suited for commercial kitchens and establishments requiring efficient cleaning of dishware, glassware, and utensils.

One of the main features of Alliance Dishwashers is their exceptional cleaning capabilities. Equipped with advanced wash systems, these dishwashers effectively utilize high-pressure jets and strategically placed spray arms to ensure thorough washing, targeting every corner of the items being cleaned. The result is spotless dishes with minimal remaining contaminants, enhancing hygiene standards in any food service environment.

The technology behind Alliance Dishwashers incorporates intelligent controls that simplify operation. With user-friendly interfaces, staff can easily select from multiple washing cycles tailored to different types of loads. This versatility allows businesses to optimize energy consumption and water usage, contributing to lower operational costs while maintaining top-notch cleaning performance.

In terms of speed, Alliance Dishwashers are engineered for rapid turnarounds, often completing washing cycles in under five minutes. This feature is particularly beneficial for high-volume settings where efficiency is paramount. Additionally, many models include a built-in heat exchanger that efficiently manages water temperatures, fostering compliance with sanitation requirements and enhancing the effectiveness of the cleaning process.

Durability is another critical characteristic of Alliance Dishwashers. Constructed with high-quality stainless steel, these units resist corrosion, withstand the rigors of continual use, and maintain their appearance over time. This not only ensures longevity but also supports the maintenance of a pristine kitchen environment which is vital in the hospitality sector.

Energy efficiency is at the core of the Alliance Dishwasher design. Many models are ENERGY STAR certified, consuming less water and electricity while delivering powerful performance. This focus on sustainability not only helps businesses reduce their environmental footprint but also leads to significant cost savings.

In conclusion, the Alliance Dishwasher combines state-of-the-art technology, user-friendly features, and robust construction to meet the demands of modern commercial kitchens. From its powerful cleaning capabilities and rapid cycle times to its energy-efficient operation, the Alliance Dishwasher is an invaluable asset for any food service operation aiming for excellence in sanitation and efficiency.