Programming

Permanent Factory Diagnostic Test

Cycle

 

 

 

Warm fill to low water level

Display flashes “bFIL”/ “LO” (keypad WASH LED on), no agitation

 

Outputs: Motor OFF, Drain closed, hot fill on, cold fill on

 

 

Pause after reaching low

Display shows “LO” (no flashing), LOW water level dot ON, no agitation (keypad WASH

water level

LED on); pauses until operator presses (∧) keypad

 

Outputs: Motor OFF, Drain closed

Drain (can advance to next

Display shows “drAI”, no agitation (keypad WASH LED on)

step by pressing (∧) keypad

 

Outputs: Motor OFF, Drain open

here)

 

 

 

Cold fill to medium level

Display flashes “CFIL”/ “nEd” (keypad WASH LED on), no agitation.

 

Outputs: Motor OFF, Drain closed, cold fill on

Pause after reaching

Display shows “nEd” (no flashing), LOW and MEDIUM water level dots ON no agitation

medium water level

(keypad WASH LED on); pauses until operator presses ^ keypad

 

Outputs: Motor OFF, Drain closed

Hot fill to high level

Display flashes “HFIL”/ “HI” (keypad WASH LED on), no agitation.

 

Outputs: Motor OFF, Drain closed, hot fill on

 

 

Pause after reaching high

Display shows “HI” (no flashing), LOW, MEDIUM, & HIGH water level dots ON, no

water level

agitation (keypad WASH LED on); pauses until operator presses ^ keypad

 

Outputs: Motor OFF, Drain closed

Heat to 45°C (110°F)

Display flashes “HEAT” and the temperature inside the machine while agitating in forward

SKIPS THIS STEP if

and reverse; continues until temperature reaches 45°C (110°F), then advances to next step.

machine does not have heat

(keypad WASH LED on)

capability (“noHt” selected

 

Outputs: Motor alternates forward 12 seconds, off 3 seconds, reverse 12 seconds, off

in SETUP Mode)

3 seconds and repeats; Drain closed; Heat ON UNTIL 45°C (110°F) reached

 

Extra fill spare – 5 seconds

Display flashes “EFIL” (keypad RINSE LED on)

(skips this if not selected in

 

Outputs: Motor alternates forward 12 seconds, off 3 seconds, reverse 12 seconds, off

SETUP Mode)

3 seconds and repeats; Drain closed; “S4” output ON.

 

 

 

Supply 1: 5 seconds (Heat

Display shows “SUP1” (keypad WASH LED on)

signal also on (IF at least

 

Outputs: Motor alternates forward 12 seconds, off 3 seconds, reverse 12 seconds, off

low water level – verifies

3 seconds and repeats; Drain closed; Supply 1 ON, HT ON, cold fill ON

output even if not heated

 

model)

 

Supply 2: 5 seconds (Heat

Display shows “SUP2” (keypad ADD BLEACH LED on)

on also)

 

Outputs: Motor alternates forward 12 seconds, off 3 seconds, reverse 12 seconds, off

 

3 seconds and repeats; Drain closed; Supply 2 ON, HT ON, cold fill ON

Supply 3: 5 seconds (Heat

Display shows “SUP3” (keypad RINSE LED on)

on also)

 

Outputs: Motor alternates forward 12 seconds, off 3 seconds, reverse 12 seconds, off

 

3 seconds and repeats; Drain closed; Supply 3 ON, HT ON, cold fill ON

Pause 5 seconds, then

Display shows “For”

Forward wash speed –

 

Outputs: Motor operates wash speed forward; drain closed

2 minutes

 

 

 

 

Table 4 (Continued)

F232157

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

29