Programming

NOTE: Temperature display applies ONLY if machine is configured for “HEAt” in SETUP Mode. Machine must be equipped with electric or steam heat and a temperature sensor. If configured for “noHt” (no heat capability) in SETUP Mode, temperature display does not appear in the segment. After temperature setting, control will skip to “drAI”/“nodr” or Spin Time, depending on version. If “HEAt”/ “noHt” does not appear in SETUP Mode, no heating is possible.

35.If display shows “drAI”/“nodr” during segment programming, a drain step option will appear at the end of the segment.

36.Select “drAI” for a drain step followed by an optional spin. Select “nodr” for no drain step.

NOTE: The machine will proceed directly to the next segment if “nodr”.

37.Change the selection by pressing the (∧) or (∨) keypad or the START (Enter) keypad to continue.

38.If “drAI” is selected (or if your model does not

provide the option of selecting “drAI”/“nodr”), the display will show “SPIn” one second, “tInE” one second, and then the time for spin: “00” (no spin) for 30-240 seconds IF you are in Rinse 1, 2, or 3. If you are in Rinse 4, the time for spin will show 0 or 1-10 minutes.

39.Change the selection by pressing the (∧) or (∨) keypad, or the START (Enter) keypad to continue.

IMPORTANT: The spin time in Rinse 4 is programmed in minutes (0-10 minutes, in one-minute increments), while other spins are in seconds to allow for shorter times (such as

45 seconds). (Rinse 4 segment should usually be used as the final rinse, even where there may be fewer than four rinses. Program zero time for preceding rinses you wish to exclude.)

40.Display shows “0000” if control cannot read temperature or a temperature if control is capable of a temperature reading.

41.Exit PROGRAM Mode by moving the Program/ Run switch back to the right as seen from the front of the machine.

NOTE: The SPIN indicator LED will automatically light during the wash cycle when the last spin programmed in a cycle is operating (regardless of which segment).

Abnormal Conditions

Door Will Not Lock

If the door handle has not been properly positioned to allow locking the door, the control will sense this and retract the door lock solenoid. The display will show “----” for about 5 seconds, then will flash “SHUt”/ “dOOr” for about 5 seconds while sounding the buzzer, prompting the user to close the door properly. The DOOR indicator LED then lights. The machine user should properly shut the door, then press START (Enter) again. If the door is still not locking correctly, the process above will repeat up to five times. After this, the display flashes “CAnt”/“LOC” (cannot lock door). The user can cause this to start over (five more attempts) by pressing START (Enter) keypad twice. If this continues, it indicates a problem, and a qualified service technician should be consulted.

Door Open During Operation

If the control senses either a momentary or sustained open door while the machine is operating in a wash cycle, the control immediately attempts to halt rotation of the cylinder. All outputs not required to effect rapid halting of the cylinder rotation de-energize immediately. The message “dOOr” then displays as long as the condition persists. Regardless of the duration of the open door condition, once it is recognized by the control, the control aborts the cycle and goes to the stop routine even if the door is closed.

Excessive Fill Time

Fill times exceeding 10 minutes cause the cycle to abort. Display flashes “StOP”/“FILL” and sounds the buzzer for 10 seconds prior to entering the stop routine (display shows “01” minutes remaining while in the stop routine). The Fill Error Count will increase by one. Refer to Cycle and Error Count section.

Out-of-Balance

If the machine goes out of balance, the machine will attempt to balance the load. After three attempts, the display will light the leftmost digit and a lower spin will be used.

WARNING

Operating the machine with severe out-of- balance loads could result in personal injury and serious equipment damage.

W728

26

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

F232157