NOTE: If temperature is not reached after 40 minutes, control resumes cycle.

After cycle resumes, control will attempt to maintain programmed temperature if it senses water in the machine.

NOTE: Temperature display applies ONLY if machine is configured for “HEAt” in SETUP Mode. Machine must be equipped with electric or steam heat and a temperature sensor. If configured for “noHt” (no heat capability) in SETUP Mode, temperature display does not appear in the segment. After temperature setting, control will skip to “drAI”/“nodr” or Spin Time, depending on version.

19.If display shows “drAI”/“nodr” during segment programming, a drain step option will appear at the end of the segment.

20.Select “drAI” for a drain step followed by an optional spin. Select “nodr” for no drain step.

NOTE: The machine will proceed directly to the next segment if “nodr”.

21.Change the selection by pressing the (∧) or (∨) keypad, or the START (Enter) keypad to continue.

22.If “drAI” is selected (or if your model does not

provide the option of selecting “drAI”/“nodr”), the display will show “SPIn” one second, “tInE” one second, and then the time for spin: “00” (no spin) or 30-240 seconds.

23.Change the selection by pressing the (∧) or (∨) keypad or the START (Enter) keypad to continue.

Rinse 1 – Rinse 4

NOTE: Programming a time other than “00” for this step will make the RINSE indicator LED light while this step is running, but not in PROGRAM Mode.

24.The main display shows “rIN1” indicating you are in the Rinse segment (number will represent Rinse cycle selected 1-4).

25.Press START (Enter) keypad. Display shows the time for agitation during the step: “00” (skips segment) or 2-15 minutes. This is the time after the fill and before the drain and does not include spin time.

26.Press the (∧) or (∨) keypad to alter the selection, or the START (Enter) keypad to continue.

Programming

27.Display shows “CFIL”, “HFIL”, “bFIL” or “EFIL” for Cold, Hot, Both (warm) or Extra fill.

28.Press the (∧) or (∨) keypad to alter the selection, or the START (Enter) keypad to continue.

NOTE: Extra fill (“EFIL”) is possible only if configured for “EFIL” in SETUP Mode. If configured, a third valve can be controlled.

29.Display shows “LO”, “nEd”, or “HI” for Low, Medium, or High water level, respectively.

30.Press the (∧) or (∨) keypad to alter the selection, or the START (enter) keypad to continue.

31.Display shows “SUP0”, “SUP1”, “SUP2”, “SUP3”, or “SUP6” (or “S 12” depending on version of control). Refer to Table 2 for operation of each supply selection.

32.Press the (∧) or (∨) keypad to alter the selection, or the START (Enter) keypad to continue.

NOTE: If programmed for “SUP2”, the ADD BLEACH indicator LED light turns on and is set up for “bEEP” the buzzer sounds for the first eight seconds Supply 2 is on.

Heated Models Only

33.Display shows temperature in degrees F or C. Display will show degrees F if configured for “FAr” in SETUP Mode, or degrees C if configured for “CEL” in SETUP Mode. Range is 80°F to 205°F, or 00F (no heat for segment), or 27°C to 95°C, or 00C (no heat for segment).

WARNING

To prevent personal injury, avoid contact with inlet water temperatures higher than 125° Fahrenheit (51° Celsius) and hot surfaces.

W748

34.Press the (∧) keypad to increase, or (∨) keypad to decrease temperature. Temperature changes in one-degree increments.

The control will energize heat and pause cycle timing for up to 40 minutes until the programmed temperature is first reached.

NOTE: If temperature not reached after 40 minutes, control resumes cycle.

After cycle resumes, control will attempt to maintain programmed temperature if it senses water in the machine.

F232157

© Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT

25